Slab Track Design and Maintenance Course
Online course of 300 hours in Slab Track Design and Maintenance: 6 modules covering slab track types, structural design of the slab, transitions and special elements, slab track construction, and maintenance and repair, with an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Compare the available slab track types.
Carry out the structural sizing of the slab and its base.
Design transitions and special elements.
Plan slab track construction in different environments.
Diagnose and repair slab track defects.
Assess life-cycle cost compared with ballasted track.
Design a complete slab track section.
Who it's for
- Track engineers.
- Railway structural designers.
- Railway site managers.
- Infrastructure maintenance engineers.
- High-speed rail consultants.
- Quality control technicians.
- Engineering or science graduates looking to enter railway infrastructure.
What you'll work with
- UNE-EN 16432-1 (ballastless track systems: general requirements)
- UNE-EN 16432-2 (ballastless track systems: system design, subsystems and components)
- UNE-EN 16432-3 (ballastless track systems: acceptance)
- Regulation (EU) 1299/2014 (TSI infrastructure)
- UNE-EN 13481-5 (fastening systems for slab track)
- UNE-EN 1992-1-1 (Eurocode 2: design of concrete structures)
- Código Estructural (Real Decreto 470/2021) (Spanish Structural Code)
- UNE-EN 13848 (track geometry quality)
- ANSYS Mechanical
- SOFiSTiK
- Autodesk Civil 3D
- MATLAB
- Microsoft Excel
6 modules
1.1Differences between slab track and ballasted track1.2Systems with embedded sleepers: Rheda and Züblin1.3Precast slab systems: Shinkansen and Bögl1.4Direct fixation and block systems1.5Slab track with elastomers and mass-spring systems1.6Systems for tram and light rail1.7Experience on European and Asian high-speed lines1.8Advantages, costs and limitations1.9Criteria for selecting the track type1.10Case study: comparison of systems on high-speed lines
2.1Vertical and horizontal actions on the slab2.2Models of a slab on an elastic foundation2.3Vertical stiffness of the system and fastenings2.4Hydraulically bound base layer2.5Reinforcement and cracking of the slab2.6Thermal actions and shrinkage2.7Fatigue of concrete and steel2.8Allowable settlements of the formation2.9Slab track in tunnels and on viaducts2.10Practical: finite element model of a slab
3.1Transition between slab track and ballasted track3.2Switches and crossings on slab track3.3Expansion joints on structures3.4Turnouts and gauge changers on slab3.5Longitudinal and transverse drainage3.6Integration of cable ducts and signalling3.7Vibration and noise attenuation3.8Maintenance and evacuation walkways3.9Edge details and protection3.10Workshop: design of a transition zone
4.1Preparation and control of the formation4.2Top-down and bottom-up construction methods4.3Slipform concreting4.4Placement of precast slabs4.5Geometric adjustment and precision levelling4.6Concrete quality control4.7Production rates and site logistics4.8Acceptance tolerances4.9Construction in tunnels4.10Case study: construction in a 5 km tunnel
5.1Defects of slab track5.2Cracking and loss of bond5.3Pumping of fines and voids beneath the slab5.4Geometric correction with adjustable fastenings5.5Replacement of precast slabs5.6Repair grouting5.7Maintenance of rails and fastenings5.8Specific monitoring of the slab5.9Life-cycle cost compared with ballasted track5.10Case study: slab repair on a high-speed line
6.1Selection of the section and constraints6.2Choice of slab track system6.3Structural calculation of the slab6.4Design of transitions6.5Drainage and integration of services6.6Construction procedure for the section6.7Maintenance plan6.8Life-cycle cost analysis6.9Report and presentation6.10Final project: final review with your tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within the intake, so it can be combined with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is ANSYS Mechanical, SOFiSTiK, Autodesk Civil 3D, MATLAB and Microsoft Excel, in free, academic or evaluation versions. Cases are studied on real procedures for sizing slab track slabs, designing ballast-to-slab transitions and assessing track life-cycle cost. Assessment is continuous by module plus the final integrated project.
Standards covered: UNE-EN 16432-1; UNE-EN 16432-2; UNE-EN 16432-3; Regulation (EU) 1299/2014; UNE-EN 13481-5; UNE-EN 1992-1-1; Código Estructural (Real Decreto 470/2021); UNE-EN 13848.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- No prior qualification is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours over 3 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with ANSYS Mechanical, SOFiSTiK, Autodesk Civil 3D, MATLAB and Microsoft Excel, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute certificate, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
No prior qualification is required: you only need an internet connection, a computer able to run the programme software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Airport and Port Intermodality Course
Online 300 h course in Airport and Port Intermodality. 6 modules covering Regulation (EU) 2024/1679, guidelines for the trans-European transport network, Directive 92/106/CEE, combined freight transport…
Smart Urbanism Course with Data Analytics
Online course of 300 hours in smart urbanism with data analytics: 6 modules covering the city as a data system, urban spatial analysis, programming for urban…
Course in Cable-Stayed Bridge Design
Online course of 300 hours in cable-stayed bridge design. 6 modules covering the conceptual design of cable-stayed bridges, stay cables and anchorages, structural analysis, deck and…
More in Civil, Rail & Smart Cities
All Civil, Rail & Smart Cities programmes → · How to apply · Fees & financing · Scholarships