Diploma in Real-Time Plant Monitoring
Online postgraduate diploma of 800 hours in real-time monitoring of nuclear plants, structured in 8 modules covering instrumentation and control, neutron and core monitoring, plant radiation monitoring, data acquisition and supervision, equipment condition monitoring, advanced analytics and qualification requirements, with an assigned technical tutor.
Diploma in Real-Time Plant Monitoring — studying from Malta
Malta has no nuclear power generation, and its nuclear engineering relevance lies mainly in radiation protection, safeguards awareness, medical and industrial radiation use, and regulatory oversight of radioactive materials. The Malta Radiation Protection Department and the Health Directorate oversee the use of radiation in hospitals, research and industry. Engineers may find roles in medical physics support, radiological monitoring and compliance. The sector is largely confined to applied and regulatory work rather than fuel cycle activity.
Fees for Malta: €1,790 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a professional route in Malta for nuclear engineering, and is SEIUM's qualification recognised?
Malta does not operate nuclear power plants, so nuclear engineering careers there are limited, and roles are more likely in regulation, consultancy or international work. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is decided by employers or the relevant regulatory body, so verify this before enrolling.
What employment could this training lead to in Malta?
Given Malta has no nuclear power generation, local opportunities are few and would mostly sit within consultancy, international organisations or firms working abroad. Employers in these roles set their own qualification requirements, and a private online qualification may or may not be accepted. Reviewing job requirements and speaking with employers will show how the training would be viewed.
Can I study this from Malta without relocating, and how is the workload structured?
Yes, the programmes are 100% online, taught in English and suitable for study from home, so you do not need a student visa. Master's programmes total 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. Each student has an assigned technical tutor, and fees are payable in instalments, with possible employer sponsorship.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand the instrumentation and control architecture of nuclear power plants.
Analyse neutron monitoring of the reactor core.
Understand plant radiation monitoring systems.
Design data acquisition and supervisory systems.
Apply condition monitoring techniques.
Use advanced analytics for diagnostics.
Apply regulatory qualification requirements.
Who it's for
- Nuclear instrumentation and control engineers
- Radiation monitoring technicians
- Supervisory systems engineers
- Plant data analysts
- Predictive maintenance engineers
- Equipment qualification engineers
- Engineering or science graduates looking to move into nuclear power plants
What you'll work with
- IEC 61513 (general requirements for I&C systems important to safety)
- IEC 60880 (software for computer-based systems performing category A functions)
- IEC 61226 (categorisation of I&C functions important to safety)
- IEC 62645 (cybersecurity requirements for nuclear I&C systems)
- IAEA SSG-39 (design of instrumentation and control systems for nuclear power plants)
- IEEE 603 (criteria for safety systems for nuclear power generating stations)
- IEC 60951 (radiation monitoring equipment for accident and post-accident conditions)
- 10 CFR 50.55a (US NRC codes and standards requirements)
- OSIsoft PI System
- MATLAB
- Python with scikit-learn
- LabVIEW
- Plant simulators
8 modules
1.1Instrumentation and control architecture1.2Safety and non-safety systems1.3Reactor protection systems1.4Classification of I&C systems1.5Process instrumentation1.6Nuclear in-core instrumentation1.7Main control room1.8Evolution towards digital systems1.9Independence and redundancy requirements1.10Case study: I&C architecture of a PWR
2.1Ex-core neutron detectors2.2Movable and fixed in-core instrumentation2.3Reactor power measurement2.4Axial power distribution2.5Self-powered neutron detectors2.6Core exit thermocouples2.7Neutron noise monitoring2.8Calibration of nuclear instrumentation2.9Technical specification limits2.10Laboratory: analysis of neutron noise signals
3.1Process radiation monitors3.2Area monitors3.3Effluent monitors3.4Primary coolant leak monitoring3.5Post-accident radiation monitors3.6Personnel dosimetry3.7Environmental radiological monitoring network3.8Integration in the control room3.9Regulatory monitoring requirements3.10Practical exercise: configuring alarms on an effluent monitor
4.1Plant process computer4.2SCADA systems in nuclear power plants4.3Data historians4.4Safety parameter display4.5Emergency response data system4.6Data transmission to the regulator4.7Human-machine interface design4.8Alarm management4.9Cybersecurity of digital systems4.10Laboratory: parameter trends in a data historian
5.1Vibration monitoring of pumps5.2Loose parts monitoring5.3Leak detection by acoustic emission5.4Monitoring of motor-operated valves5.5Monitoring of main transformers5.6Turbine and generator monitoring5.7Thermography in the plant5.8Condition-based maintenance5.9Ageing management5.10Practical exercise: diagnosis of a coolant pump
6.1Online signal validation6.2Online sensor calibration monitoring6.3Anomaly detection6.4Empirical process models6.5Machine learning in nuclear power plants6.6Plant digital twins6.7Operator support systems6.8Explainability of algorithms6.9Software qualification6.10Laboratory: validation of redundant signals
7.1IEC SC 45A standards7.2IAEA guides for I&C7.3Environmental and seismic qualification7.4Safety-category software7.5Diversity and defence in depth7.6Common cause failure7.7Requirements of the Nuclear Safety Council (CSN)7.8Management of design modifications7.9Cybersecurity according to IEC 626457.10Case study: modernisation of a supervisory system
8.1Selection of the plant system8.2Requirements analysis8.3Sensor selection8.4Acquisition architecture8.5Diagnostic functions8.6Qualification plan8.7Design conclusions8.8Implementation recommendations8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
The programme is delivered 100% online on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so it fits alongside your job.
Each module combines theory, guided reading of the original standards and applied exercises. You work with OSIsoft PI System, MATLAB, Python with scikit-learn, LabVIEW and plant simulators in free, academic or evaluation versions. Practical work is based on real procedures for online signal validation, neutron noise analysis and diagnosis of rotating equipment. Assessment is continuous by module, plus a final capstone project.
Standards covered: IEC 61513, IEC 60880, IEC 61226, IEC 62645, IAEA SSG-39, IEEE 603, IEC 60951, 10 CFR 50.55a.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with OSIsoft PI System, MATLAB, Python with scikit-learn, LabVIEW and plant simulators, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in Monitoring and Security in Transport
Online postgraduate diploma of 800 hours in monitoring and security in the transport of nuclear and radioactive material, structured in 8 modules covering the nuclear security…
Diploma in Long-Term Safety Monitoring
Online postgraduate diploma of 800 hours in long-term safety monitoring of nuclear and waste facilities, structured in 8 modules covering long-term safety, surveillance programmes, hydrogeological, geotechnical…
Diploma in Radiological Impact on Fauna and Flora
Online postgraduate diploma of 800 hours in radiological impact on fauna and flora. 8 modules covering environmental radioactivity, transfer in ecosystems, dosimetry of non-human biota, biological…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships