Diploma in FADEC Control Systems and Safety
Online postgraduate diploma of 800 hours in FADEC Control Systems and Safety. 8 modules covering gas turbines and their control, control laws, FADEC architecture, system safety (ARP4754A, ARP4761), critical software (DO-178C), complex electronic hardware (DO-254) and testing, certification and diagnostics, with an assigned technical tutor.
Diploma in FADEC Control Systems and Safety — studying from Canada
Canada's defence sector is centred on procurement and sustainment through the Department of National Defence and Defence Research and Development Canada. Industrial activity spans land vehicles, naval systems, avionics and electronics, with firms in Ontario, Québec, Nova Scotia and British Columbia. Companies such as General Dynamics Land Systems Canada and Lockheed Martin Canada are notable employers, alongside a broad base of small and medium suppliers. Engineers work on systems integration, vehicle protection, logistics and sustainment, operating within strict security and export control frameworks.
Fees for Canada: C$2,790 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Which Canadian bodies or processes govern defence engineering recognition?
Defence engineering in Canada often involves government procurement and security clearances, and engineers typically hold provincial Professional Engineer licences where a title is required. SEIUM's qualifications are private and not official state degrees or accredited by a national body, so they do not confer licensing or clearance. Recognition is for employers or the relevant body to decide, so verify this first.
Would Canadian defence or land systems employers accept this training?
Canadian defence employers and contractors generally rely on security clearance, licensing and demonstrated experience. A private qualification may support your application, but it is unlikely to replace those requirements, and its acceptance is up to each employer. A SEIUM final project can help show applied skill, so discuss expectations with prospective employers early.
Can I study remotely while working, and what are the costs and language demands?
Yes, the programmes are fully online, so you can study from Canada or elsewhere without a student visa, and fit sessions around work. Specialist courses are 300 hours, postgraduate diplomas 800 and master's 1,900. Teaching is in English, supported by an assigned technical tutor. Fees are payable in instalments, and employer sponsorship may be available.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand how gas turbines work and what they require from their control system.
Design engine control and protection laws.
Analyse the redundant architecture of FADEC systems.
Apply development processes for critical software and hardware.
Assess the safety of the control system.
Plan verification and certification.
Manage maintenance and diagnostics of the control system.
Who it's for
- Engine control engineers.
- Critical embedded software engineers.
- Aircraft systems safety engineers.
- Engine certification engineers.
- Engine test engineers.
- Aerospace hardware engineers.
- Engineering or science graduates seeking to enter the aerospace sector.
What you'll work with
- RTCA DO-178C (software in airborne systems)
- RTCA DO-254 (airborne electronic hardware)
- RTCA DO-160G (environmental conditions for airborne equipment)
- SAE ARP4754A (development of civil aircraft and systems)
- SAE ARP4761 (system safety assessment)
- EASA CS-E (certification specifications for engines)
- 14 CFR 33.28 (engine control systems)
- MIL-HDBK-516C (airworthiness certification criteria)
- MATLAB/Simulink
- ANSYS SCADE Suite
- LDRA Testbed
- Polyspace
- GasTurb
8 modules
1.1The Brayton cycle1.2Turbofans and turboshafts1.3Compressor maps and surge margins1.4Engine dynamics1.5Controlled and measured variables1.6History of hydromechanical control1.7Evolution towards FADEC1.8Control requirements1.9Interface with the aircraft1.10Case study: analysis of a compressor map
2.1Thrust control2.2Acceleration and deceleration control2.3Fuel scheduling2.4Variable geometry control2.5Overspeed protection2.6Temperature limits2.7Start-up and shutdown2.8Multivariable control2.9Control robustness2.10Lab: thrust control law in Simulink
3.1Redundant channels3.2Sensors and actuators3.3Fuel metering unit3.4Electrical power supply3.5Communications with the aircraft3.6Fault management3.7Degraded modes3.8Mechanical integration3.9DO-160G environmental conditions3.10Practical exercise: redundant FADEC architecture
4.1The ARP4754A process4.2ARP4761 safety assessment4.3Functional hazard assessment4.4Control system fault trees4.5Allocation of development assurance levels4.6Common cause failures4.7CS-E and 14 CFR 33.28 requirements4.8Zonal analysis4.9Time-limited dispatch4.10Case study: safety analysis of a FADEC
5.1Planning according to DO-178C5.2High-level and low-level requirements5.3Model-based design5.4Automatic code generation5.5Verification by review and analysis5.6MC/DC structural coverage5.7Static analysis5.8Tool qualification5.9Configuration management5.10Lab: structural coverage analysis
6.1The DO-254 process6.2FPGAs and ASICs in engine control6.3Hardware verification6.4Timing analysis6.5Radiation effects6.6Component reliability6.7Obsolescence6.8Environmental testing6.9Electromagnetic compatibility6.10Practical exercise: FPGA verification plan
7.1System rig testing7.2Engine test cell testing7.3Flight testing7.4Engine certification7.5Engine health monitoring7.6Fault diagnosis7.7FADEC maintenance7.8Software updates7.9In-service experience7.10Workshop: certification plan for a software change
8.1Engine definition8.2Control requirements specification8.3Control law design8.4System architecture8.5Safety analysis8.6Software and hardware plan8.7Verification plan8.8Conclusions8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so the programme fits around your job.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is MATLAB/Simulink, ANSYS SCADE Suite, LDRA Testbed, Polyspace and GasTurb, in free, academic or evaluation versions. Practical work is based on real procedures: designing a thrust control law in Simulink, the safety analysis of a FADEC system and software verification with structural coverage. Assessment is continuous by module, plus the final project.
Standards covered: RTCA DO-178C, RTCA DO-254, RTCA DO-160G, SAE ARP4754A, SAE ARP4761, EASA CS-E, 14 CFR 33.28, MIL-HDBK-516C.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with MATLAB/Simulink, ANSYS SCADE Suite, LDRA Testbed, Polyspace and GasTurb, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the software, and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in RAM Materials and Stealth Techniques
Online postgraduate diploma of 800 hours in radar-absorbing materials (RAM) and stealth techniques. 8 modules covering the electromagnetics of materials, radar cross section, resonant absorbers, absorbing…
Diploma in Ethics of Protective Materials Development
Online postgraduate diploma of 800 hours in ethics of protective materials development. 8 modules covering protective materials technology, ethics of innovation, the PPE and chemicals regulatory…
Diploma in Fuel Enrichment and Fabrication
Online postgraduate diploma of 800 hours in nuclear fuel enrichment and fabrication. 8 modules covering conversion to hexafluoride, enrichment and safeguards, ceramic pellet fabrication, cladding and…
More in Defense, Military Engineering & Land Systems
All Defense, Military Engineering & Land Systems programmes → · How to apply · Fees & financing · Scholarships