Diploma in Diesel-Electric Propulsion and Energy Management
Online postgraduate diploma of 800 hours in diesel-electric propulsion and energy management. 8 modules covering propulsion architectures, generating plants, distribution, converters, power quality, energy management and hybridisation, with an assigned technical tutor.
Diploma in Diesel-Electric Propulsion and Energy Management — studying from Canada
Canada's defence sector is centred on procurement and sustainment through the Department of National Defence and Defence Research and Development Canada. Industrial activity spans land vehicles, naval systems, avionics and electronics, with firms in Ontario, Québec, Nova Scotia and British Columbia. Companies such as General Dynamics Land Systems Canada and Lockheed Martin Canada are notable employers, alongside a broad base of small and medium suppliers. Engineers work on systems integration, vehicle protection, logistics and sustainment, operating within strict security and export control frameworks.
Fees for Canada: C$2,790 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Which Canadian bodies or processes govern defence engineering recognition?
Defence engineering in Canada often involves government procurement and security clearances, and engineers typically hold provincial Professional Engineer licences where a title is required. SEIUM's qualifications are private and not official state degrees or accredited by a national body, so they do not confer licensing or clearance. Recognition is for employers or the relevant body to decide, so verify this first.
Would Canadian defence or land systems employers accept this training?
Canadian defence employers and contractors generally rely on security clearance, licensing and demonstrated experience. A private qualification may support your application, but it is unlikely to replace those requirements, and its acceptance is up to each employer. A SEIUM final project can help show applied skill, so discuss expectations with prospective employers early.
Can I study remotely while working, and what are the costs and language demands?
Yes, the programmes are fully online, so you can study from Canada or elsewhere without a student visa, and fit sessions around work. Specialist courses are 300 hours, postgraduate diplomas 800 and master's 1,900. Teaching is in English, supported by an assigned technical tutor. Fees are payable in instalments, and employer sponsorship may be available.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand diesel-electric propulsion architectures in ships.
Size generating plants and distribution systems.
Analyse power converters and propulsion motors.
Assess power quality and harmonics.
Design on-board energy management systems.
Integrate energy storage and hybrid propulsion.
Apply naval electrical and environmental regulations.
Who it's for
- Naval electrical engineers.
- Propulsion engineers.
- Chief engineers looking to deepen their knowledge of electric plants.
- Energy management engineers in the maritime sector.
- Power systems engineers moving into marine applications.
- Naval automation engineers.
- Engineering or science graduates looking to enter naval defence.
What you'll work with
- IEC 60092-501 (electrical installations in ships: electric propulsion plant)
- IEC 61892 (mobile and fixed offshore units: electrical installations)
- ISO 8528 (reciprocating internal combustion engine driven generating sets)
- IEEE 519 (harmonic control in electric power systems)
- IEEE 45 (electrical installations on shipboard)
- STANAG 1008 (electrical power systems in naval ships)
- MARPOL Annex VI (prevention of air pollution from ships)
- MATLAB/Simulink Simscape Electrical
- ETAP
- DIgSILENT PowerFactory
- PSCAD
8 modules
1.1Mechanical versus electric propulsion1.2Diesel-electric configurations1.3CODLAG hybrid propulsion1.4Integrated electrical system1.5Operational advantages1.6Ship operating profiles1.7Redundancy and survivability1.8Examples in warships and civil vessels1.9Electrification trends1.10Case study: architecture selection for a patrol vessel
2.1Medium- and high-speed diesel engines2.2Synchronous generators2.3Generating sets according to ISO 85282.4Load sharing2.5Voltage and frequency regulation2.6Specific fuel consumption2.7Plant sizing2.8Starting and synchronisation2.9Generating set maintenance2.10Practical exercise: sizing a generating plant
3.1Main and emergency switchboards3.2AC distribution3.3DC distribution3.4Medium voltage on board3.5Protection and selectivity3.6Short circuits3.7Earthing3.8IEC 60092 standards3.9STANAG 1008 requirements3.10Lab: load flow study with ETAP
4.1Induction motors4.2Synchronous and permanent-magnet motors4.3Frequency converters4.4Multilevel topologies4.5Vector control and direct torque control4.6Azimuth thrusters4.7Fixed- and controllable-pitch propellers4.8Drivetrain efficiency4.9Equipment cooling4.10Practical exercise: simulation of a propulsion drive
5.1Harmonics and their effects5.2Limits according to IEEE 5195.3Passive and active filters5.4Transients and voltage dips5.5Power factor5.6Electromagnetic compatibility5.7Power quality measurements5.8Stability studies5.9Pulsed loads5.10Lab: harmonic analysis
6.1Power management systems6.2Optimal generator dispatch6.3Priority load management6.4Heat recovery6.5Energy efficiency at sea6.6Efficiency indicators6.7Emissions and MARPOL Annex VI6.8Alternative fuels6.9Energy monitoring6.10Case study: optimisation of generator dispatch
7.1Marine batteries7.2Supercapacitors7.3Hybrid operating modes7.4Silent running7.5Battery safety on board7.6Fuel cells on ships7.7Shore power connection in port7.8Control of hybrid systems7.9Life cycle analysis7.10Workshop: design of a hybrid battery system
8.1Definition of the vessel and operating profile8.2Proposed architecture8.3Sizing of the generating plant8.4Distribution design8.5Propulsion selection8.6Power quality study8.7Energy management strategy8.8Emissions assessment8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so it fits around your job.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is MATLAB/Simulink Simscape Electrical, ETAP, DIgSILENT PowerFactory and PSCAD, in free, academic or evaluation versions. Practical work is based on real procedures: a load flow study of a naval electrical plant, harmonic analysis of propulsion converters and optimisation of generator dispatch. Assessment is continuous by module, plus the final integrating project.
Standards covered: IEC 60092-501, IEC 61892, ISO 8528, IEEE 519, IEEE 45, STANAG 1008, MARPOL Annex VI.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with MATLAB/Simulink Simscape Electrical, ETAP, DIgSILENT PowerFactory and PSCAD, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the programme software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in EMAR and Military EASA
Online postgraduate diploma of 800 hours in EMAR and military EASA airworthiness, with 8 modules covering the European airworthiness framework, EMAR 21, EMAR M, EMAR 145,…
Postgraduate Diploma in Undercarriage for Extreme Climates
Online postgraduate diploma of 800 hours in running gear for extreme climates, with 8 modules covering extreme environments and mobility, wheel and track terramechanics, materials for…
Diploma in Neutron Damage and Swelling
Online postgraduate diploma of 800 hours in neutron damage and swelling: 8 modules covering displacement damage, cascades, void swelling theory, metallurgical factors, component consequences, experimental techniques…
More in Defense, Military Engineering & Land Systems
All Defense, Military Engineering & Land Systems programmes → · How to apply · Fees & financing · Scholarships