Diploma in Class A Surfaces: G3/G4 Continuity and Optical Quality
Online postgraduate diploma of 800 hours in Class A surfaces, G3/G4 continuity and optical quality, structured in 8 modules covering curve and surface geometry, geometric continuity, optical quality, Class A construction, modelling tools, feasibility and surface approval, with an assigned technical tutor.
Diploma in Class A Surfaces: G3/G4 Continuity and Optical Quality — studying from Canada
Product design and human-machine interface work is well established in Canada across automotive, aerospace, medical devices and consumer electronics. Design studios and engineering firms in Toronto, Montréal, Waterloo and Vancouver develop user interfaces for vehicles, industrial equipment and healthcare technology. Usability and accessibility requirements are shaped by national standards and provincial legislation, including the Accessible Canada Act at the federal level. Typical employers include manufacturers, software companies and design consultancies.
Fees for Canada: C$2,010 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Is design or HMI work in Canada regulated, and how does SEIUM fit in?
Product and HMI design is generally not a licensed profession in Canada, unlike engineering, which is regulated by provincial associations issuing Professional Engineer licences. SEIUM's qualifications are private, not official state degrees and not accredited by a national body. Recognition is decided by employers or relevant bodies, so confirm acceptance with them before enrolling.
Do Canadian product and interface design employers value this kind of study?
Canadian design employers, including software firms in Toronto, Montreal and Vancouver, usually focus on portfolios, user research and shipped work. A SEIUM qualification may add to your profile, especially with a strong final project, but whether it is valued depends on each employer. Build your portfolio alongside your studies.
How much time does this need alongside work, and how is it paid for?
The courses are fully online, so you can study from home at your own pace. Specialist courses take 300 hours, postgraduate diplomas 800 and master's 1,900, so consider your weekly availability. Teaching is in English with an assigned technical tutor. Fees can be paid in instalments, and employer sponsorship is possible, which you can ask your employer about.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Master NURBS geometry applied to bodywork surfaces.
Build transitions with G2, G3 and G4 continuity.
Evaluate optical quality with zebra stripes, isophotes and curvature combs.
Plan the patch strategy for Class A surfaces.
Use Alias, ICEM Surf and CATIA in production workflows.
Verify the stamping and injection feasibility of surfaces.
Document and approve surfaces for the tooling phase.
Who it's for
- Class A surface modellers aiming to master G3/G4 continuity and optical quality.
- Digital automotive designers.
- Body surface engineers.
- Perceived quality specialists.
- Product CAD modellers.
- Tooling feasibility engineers.
- Engineering or science graduates seeking to enter the automotive industry.
What you'll work with
- ISO 10303-242 (STEP AP242, managed model-based 3D engineering)
- ISO 10303-214 (STEP AP214 for automotive design)
- VDA 4955 (scope and quality of CAD/CAM data)
- ISO 16792:2021 (digital product definition data practices)
- VDA 4956 (product data exchange)
- ISO 1101:2017 (geometrical product specifications)
- Autodesk Alias Surface
- ICEM Surf
- CATIA V5/3DEXPERIENCE
- Rhinoceros
- VRED
8 modules
1.1Bézier, B-spline and NURBS curves1.2Degree, order and knot vectors1.3Control points and weights1.4Curvature, torsion and radius of curvature1.5NURBS surfaces and patches1.6Gaussian and mean curvature1.7Developable and ruled surfaces1.8Patch topology in bodywork1.9Precision and tolerances in CAD1.10Workshop: curvature analysis of a bonnet section
2.1G0, G1 and G2 continuity2.2G3 continuity and curvature variation2.3G4 continuity and curvature acceleration2.4Differences between parametric and geometric continuity2.5Corner transitions and three-way junctions2.6Curvature-continuous fillets versus radii2.7Blend surfaces and connecting surfaces2.8Diagnosing discontinuities2.9Angular and positional tolerances2.10Practical exercise: G3 transition between roof and pillar
3.1Reflections and visual perception of form3.2Zebra and reflection lines3.3Highlight lines and isophotes3.4Environment lighting analysis3.5Curvature combs and diagnosis3.6Colour curvature maps3.7Optical defects: waviness and flat spots3.8Influence of finish and paint3.9Acceptance criteria in the studio3.10Lab: reflection evaluation with zebra stripes
4.1Patch strategy and surface layout4.2Primary, secondary and connecting surfaces4.3Control point management and distribution4.4High-degree versus multispan surfaces4.5Character lines and sharp edges4.6Joints, gaps and flush between parts4.7Demoulding and draft angles4.8Integrating headlamps and rear lamps4.9Glass surfaces and optical requirements4.10Case study: side door in Class A
5.1Autodesk Alias Surface and AutoStudio5.2ICEM Surf in production workflows5.3CATIA ICEM Shape Design5.4Continuity analysis tools5.5Scanning and reconstruction from clay5.6Reverse engineering of physical models5.7Data exchange with STEP and IGES formats5.8Surface version management5.9Productivity and workflow shortcuts5.10Workshop: surface reconstruction from a scan
6.1Sheet metal stamping requirements6.2Minimum radii and deformation6.3Surfaces of injection-moulded plastic parts6.4Springback compensation6.5Coordination with body engineering6.6Fit and finish: gap & flush6.7Deep drawing simulation6.8Validation on a physical clay model6.9Virtual reality visualisation6.10Practical exercise: feasibility check of a panel
7.1Review cycles with design7.2Quality criteria by visible zone7.3Surface quality reports7.4Version comparison and deviations7.5Surface freeze for tooling7.6Change documentation7.7Coordination with tooling suppliers7.8Perceived quality audits7.9Communication with the design studio7.10Case study: approval report for a bonnet
8.1Selecting an exterior component8.2Analysis of the starting model8.3Patch strategy8.4Modelling primary surfaces8.5G3 continuity and blends8.6Optical evaluation and feasibility8.7Quality report8.8Final reflection corrections8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
The programme is delivered 100% online on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within the intake, making it compatible with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is Autodesk Alias Surface, ICEM Surf, CATIA V5/3DEXPERIENCE, Rhinoceros, VRED, in free, academic or evaluation versions. Tests are studied on real procedures: building exterior surfaces with G3 continuity, evaluating reflections and optical quality in the studio, and checking stamping feasibility. Assessment is continuous by module plus the final capstone project.
Standards covered: ISO 10303-242 (STEP AP242), ISO 10303-214 (STEP AP214), VDA 4955, ISO 16792:2021, VDA 4956, ISO 1101:2017.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme's software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with Autodesk Alias Surface, ICEM Surf, CATIA V5/3DEXPERIENCE, Rhinoceros and VRED, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the software, and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in Intelligent Surfaces “Hidden-until-Lit”
Online postgraduate diploma of 800 hours in “hidden-until-lit” smart surfaces: 8 modules covering semi-translucent materials, hidden graphics and lighting, sensors and interaction, IME manufacturing, ergonomics and…
Diploma in Trim Processes, Joining and Perceived Quality
Online postgraduate diploma of 800 hours in trim processes, joining and perceived quality: 8 modules covering interior trim components, trim manufacturing processes, joining technologies, perceived quality,…
Diploma in High-End Sensory Experience
Online postgraduate diploma of 800 hours in high-end sensory experience, structured in 8 modules covering sensory perception, haptic, sound, olfactory and lighting design, integrated experiences and…
More in Design, HMI & Product
All Design, HMI & Product programmes → · How to apply · Fees & financing · Scholarships