Diploma in Sectoral Regulation and Validation
Online postgraduate diploma of 800 hours in sector regulation and validation: 8 modules covering the regulatory framework, quality risk management, the validation lifecycle, computerised systems, validation in non-pharmaceutical sectors, documentation and inspections under EudraLex Volume 4 Annex 15, Annex 11 and FDA 21 CFR Part 11, with an assigned technical tutor.
Diploma in Sectoral Regulation and Validation — studying from Singapore
Singapore is a leading robotics and automation centre, with strong activity in logistics automation, industrial robotics and smart manufacturing. The Agency for Science, Technology and Research and Nanyang Technological University support robotics research, while the Economic Development Board promotes automation adoption. Engineers work on control systems, industrial automation, mobile robots and warehouse systems. Employers include multinational automation suppliers, logistics operators and manufacturers modernising their plants.
Fees for Singapore: S$1,560 (Singapore dollar), with instalments and employer sponsorship available.
Relevant bodies in Singapore
Typical roles
Questions from Singapore
Will this qualification be recognised by professional bodies in Singapore?
SEIUM's qualifications are private, not official state degrees, and are not accredited by any national body in Singapore. Engineers in Singapore can seek Professional Engineer status through the Professional Engineers Board, and the Institution of Engineers Singapore is a professional body for engineers. Recognition of a private qualification is decided by employers or the relevant body.
How might this training be used by employers in Singapore?
Singapore's manufacturing, logistics, electronics and smart-facility sectors use automation and control systems extensively, so these skills may suit roles in systems integration, controls engineering or automation support. The programme does not guarantee employment. Employers will usually look at your practical projects and experience alongside the qualification.
Can I study this alongside a full-time job, and can my employer help fund it?
Study is entirely online and in English, with an assigned technical tutor, so you can fit it around a job in Singapore. Master's programmes take 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. Fees can be paid in instalments, and employer sponsorship is possible; automation teams in many firms may support relevant training.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Interpret the regulatory framework of the pharmaceutical, healthcare and food sectors.
Apply quality risk management according to ICH Q9.
Plan the validation lifecycle from URS to PQ.
Validate computerised systems in line with Annex 11 and 21 CFR Part 11.
Adapt process validation to non-pharmaceutical sectors.
Produce validation documentation following ALCOA+ principles.
Prepare the organisation for regulatory inspections.
Who it's for
- Validation technicians.
- Regulatory affairs managers.
- Equipment qualification engineers.
- GxP computerised systems specialists.
- Quality auditors.
- Process engineers in regulated industries.
- Engineering or science graduates seeking to move into the pharmaceutical industry.
What you'll work with
- EudraLex Volume 4 Annex 15 (qualification and validation)
- EudraLex Volume 4 Annex 11 (computerised systems)
- FDA 21 CFR Part 11 (electronic records and signatures)
- ICH Q9(R1) (quality risk management)
- ICH Q10 (pharmaceutical quality system)
- ISO 13485:2016 (medical devices quality management)
- Regulation (EU) 2017/745 (medical devices)
- ISO 11607-2:2019 (validation of packaging processes)
- Kneat Gx
- ValGenesis VLMS
- MasterControl
- Veeva Vault QualityDocs
- Minitab
8 modules
1.1Regulated sectors and their rationale1.2The EMA, FDA and AESAN agencies1.3Directive 2001/83/EC and pharmaceutical legislation1.4EudraLex Volume 4 GMP1.5Regulation (EU) 2017/745 on medical devices1.6General food law1.7Cosmetics and Regulation (EC) 1223/20091.8Impact on plant automation1.9Inspections and their consequences1.10Case study: regulatory map of a multi-sector plant
2.1ICH Q9 and risk management2.2FMEA, HACCP and FTA tools2.3System impact assessment2.4Critical quality attributes2.5Critical process parameters2.6Risk-based change control2.7Periodic risk review2.8Documenting risk management2.9Integration with the ICH Q10 quality system2.10Workshop: FMEA of an automated dosing system
3.1Validation master plan3.2User requirements specification3.3Design qualification (DQ)3.4Installation qualification (IQ)3.5Operational qualification (OQ)3.6Performance qualification (PQ)3.7Process validation according to the 2011 FDA guidance3.8EudraLex Annex 153.9Continued process verification3.10Practical exercise: structure of a VMP for a packaging plant
4.1EudraLex Annex 114.2FDA 21 CFR Part 114.3Electronic records and signatures4.4Audit trails4.5Validation of SCADA and MES systems4.6Software supplier management4.7Backup and recovery4.8Access control and user profiles4.9Periodic system review4.10Case study: assessment of a SCADA system against Annex 11
5.1Process validation in medical devices5.2ISO 13485 and special processes5.3Sterilisation validation according to ISO 11135 and ISO 176655.4Validation of CCPs in the food industry5.5Analytical method validation5.6Packaging process validation to ISO 116075.7Cleaning validation5.8Differences between sectors5.9Harmonising approaches5.10Practical exercise: validation protocol for package sealing
6.1Good documentation practices6.2ALCOA+ principles6.3Validation protocols and reports6.4Deviation management in validation6.5Requirements traceability matrix6.6Record archiving and retention6.7Document review and approval6.8Electronic document management systems6.9Inspection readiness6.10Workshop: OQ protocol with acceptance criteria
7.1Preparing for regulatory inspections7.2How an inspection unfolds7.3Observations and Form 4837.4Warning letters and their causes7.5CAPA plans following inspection7.6Supplier audits7.7Quality and compliance culture7.8Ethics and integrity in regulated industry7.9Current regulatory trends7.10Case study: analysis of warning letters relating to automation
8.1Selection of the process and sector8.2Applicable regulatory analysis8.3Quality risk assessment8.4Validation master plan8.5Qualification protocols8.6Computerised system validation8.7Traceability matrix8.8Compliance assessment8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
Training is 100% online on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, making it compatible with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is Kneat Gx, ValGenesis VLMS, MasterControl, Veeva Vault QualityDocs and Minitab, in free, academic or evaluation versions. Tests are studied on real procedures: drafting a validation master plan, IQ/OQ qualification of automated equipment, and compliance assessment of a computerised system. Assessment is continuous by module plus the final project.
Standards covered: EudraLex Volume 4 Annex 15, EudraLex Volume 4 Annex 11, FDA 21 CFR Part 11, ICH Q9(R1), ICH Q10, ISO 13485:2016, Regulation (EU) 2017/745, ISO 11607-2:2019.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- Internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with Kneat Gx, ValGenesis VLMS, MasterControl, Veeva Vault QualityDocs and Minitab, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer capable of running the software, and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in Interface Design and Operator Confidence
Online postgraduate diploma of 800 hours in interface design and operator trust: 8 modules covering human-robot interaction, trust in automation, interface design principles, multimodal interfaces, communication…
Diploma in Traceability and Quality in Processing
Online postgraduate diploma of 800 hours in traceability and quality in processing: 8 modules covering quality systems, product traceability, MES and electronic records, statistical process control,…
Diploma in Vision-Guided Integration for Welding
Online postgraduate diploma of 800 hours in vision-guided integration for welding: 8 modules covering machine vision in robotic welding, vision system calibration, joint detection and localisation,…
More in Robotics, Automation & Control
All Robotics, Automation & Control programmes → · How to apply · Fees & financing · Scholarships