Diploma in Multispectral Camouflage Validation Testing
Online postgraduate diploma of 800 hours in multispectral camouflage validation testing. 8 modules covering signatures and perception, camouflage materials, laboratory spectral measurement, thermal and infrared testing, radar testing, field trials and observation, and standards, quality and ethics, with an assigned technical tutor.
Diploma in Multispectral Camouflage Validation Testing — studying from Canada
Canada's defence sector is centred on procurement and sustainment through the Department of National Defence and Defence Research and Development Canada. Industrial activity spans land vehicles, naval systems, avionics and electronics, with firms in Ontario, Québec, Nova Scotia and British Columbia. Companies such as General Dynamics Land Systems Canada and Lockheed Martin Canada are notable employers, alongside a broad base of small and medium suppliers. Engineers work on systems integration, vehicle protection, logistics and sustainment, operating within strict security and export control frameworks.
Fees for Canada: C$2,010 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Which Canadian bodies or processes govern defence engineering recognition?
Defence engineering in Canada often involves government procurement and security clearances, and engineers typically hold provincial Professional Engineer licences where a title is required. SEIUM's qualifications are private and not official state degrees or accredited by a national body, so they do not confer licensing or clearance. Recognition is for employers or the relevant body to decide, so verify this first.
Would Canadian defence or land systems employers accept this training?
Canadian defence employers and contractors generally rely on security clearance, licensing and demonstrated experience. A private qualification may support your application, but it is unlikely to replace those requirements, and its acceptance is up to each employer. A SEIUM final project can help show applied skill, so discuss expectations with prospective employers early.
Can I study remotely while working, and what are the costs and language demands?
Yes, the programmes are fully online, so you can study from Canada or elsewhere without a student visa, and fit sessions around work. Specialist courses are 300 hours, postgraduate diplomas 800 and master's 1,900. Teaching is in English, supported by an assigned technical tutor. Fees are payable in instalments, and employer sponsorship may be available.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand visible, infrared and radar signatures.
Know the materials used in multispectral camouflage.
Carry out traceable laboratory spectral measurements.
Perform thermal and radiometric tests.
Measure the radar reflectivity of materials.
Design field evaluation campaigns.
Prepare test reports in line with quality standards.
Who it's for
- Materials testing engineers.
- Multispectral signature specialists seeking a structured grounding in validation testing.
- Testing laboratory technicians working with spectral, thermal or radar measurements.
- Remote sensing engineers.
- Test quality managers.
- Researchers in functional materials.
- Engineering or science graduates seeking to enter the defence sector.
What you'll work with
- ISO/IEC 17025 (competence of testing laboratories)
- ASTM E903 (solar reflectance of materials)
- ASTM E1933 (emissivity measurement by thermography)
- CIE 15:2018 (colorimetry)
- IEEE Std 1128 (measurement of radio-frequency absorbers)
- ISO 18434-1 (thermography in condition monitoring)
- MATLAB
- OKTAL-SE
- ENVI
- CST Studio Suite
- FLIR Research Studio
8 modules
1.1Visible, infrared and radar spectrum1.2Contrast and detectability1.3Human visual perception1.4Johnson criteria1.5Infrared signature and emissivity1.6Radar signature and reflectivity1.7Multispectral and hyperspectral signatures1.8Environmental factors1.9Background and natural environment1.10Case study: contrast analysis against different backgrounds
2.1Pigments with near-infrared reflectance2.2Technical textiles2.3Low-emissivity materials2.4Radar absorbers2.5Metamaterials2.6Adaptive coatings2.7Durability and ageing2.8Material sustainability2.9Manufacturing and batch control2.10Laboratory: reflectance spectrum of fabrics
3.1UV-VIS-NIR spectrophotometry3.2Integrating spheres3.3Emissivity measurement with FTIR3.4Calibration and reference standards3.5Measurement uncertainty3.6Sampling and specimen preparation3.7CIE colorimetry3.8Background databases3.9Material testing standards3.10Practical: emissivity measurement with FTIR
4.1MWIR and LWIR thermographic cameras4.2Radiometric calibration4.3Apparent thermal contrast4.4Climatic chamber testing4.5Outdoor testing4.6Influence of solar radiation4.7Thermal modelling4.8Simulation with signature software4.9Performance metrics4.10Laboratory: thermographic test of a tarpaulin
5.1Radar cross section5.2Anechoic chambers5.3Open-field measurements5.4Test frequency bands5.5Reflection coefficient5.6NRL arch method5.7Electromagnetic simulation5.8Uncertainty in radar measurements5.9Measurement-simulation correlation5.10Practical: reflectivity measurement with the NRL arch
6.1Design of field campaigns6.2Observer panels6.3Photosimulation and evaluation6.4Statistical analysis of detection6.5Trials with airborne sensors6.6Hyperspectral remote sensing6.7Trials across different seasons6.8Test logistics6.9Safety and environment6.10Case study: design of an evaluation campaign
7.1Applicable STANAG and AEP standards7.2National technical specifications7.3ISO/IEC 17025 laboratory accreditation7.4Quality management7.5Test reports7.6Confidentiality of results7.7Export control7.8Ethics of developing concealment technologies7.9Environmental responsibility7.10Case study: audit of a test report
8.1Definition of the material8.2Signature requirements8.3Laboratory test plan8.4Field test plan8.5Uncertainty analysis8.6Evaluation of results8.7Conformity report8.8Recommendations for improvement8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
A 100% online programme on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so it can be combined with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is MATLAB, OKTAL-SE, ENVI, CST Studio Suite and FLIR Research Studio, in free, academic or evaluation versions. Testing is studied through real procedures for spectral reflectance and emissivity measurements, thermographic tests in climatic chambers and field observation campaigns. Assessment is continuous by module plus the final integrating project.
Standards covered: ISO/IEC 17025, ASTM E903, ASTM E1933, CIE 15:2018, IEEE Std 1128, ISO 18434-1.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with MATLAB, OKTAL-SE, ENVI, CST Studio Suite and FLIR Research Studio, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in MIL-STD-461/464: Military EMC/EMI
Online postgraduate diploma of 800 hours in military EMC/EMI to MIL-STD-461/464. 8 modules covering electromagnetic compatibility fundamentals, MIL-STD-461G, laboratory testing, system-level MIL-STD-464C, design for EMC, diagnosis…
Diploma in Autonomous Ground and Underground Robotics
Online postgraduate diploma of 800 hours in autonomous ground and underground robotics. 8 modules covering mobile robot platforms, perception, localisation and mapping, planning and control, underground…
Diploma in NATO Defence Architectures
Online postgraduate diploma of 800 hours in NATO defence architectures. 8 modules covering NATO and its structure, the NATO Architecture Framework, Federated Mission Networking, the C3…
More in Defense, Military Engineering & Land Systems
All Defense, Military Engineering & Land Systems programmes → · How to apply · Fees & financing · Scholarships