Postgraduate Diploma in QA of Prepreg/Autoclave and Rapid Cure
Online 800-hour Postgraduate Diploma in QA of Prepreg/Autoclave and Rapid Cure. 8 modules with AS9100D aerospace quality management, SAE AMS 2750 pyrometry and Ansys Composite Cure Simulation. Assigned tutor and open enrolment.
Postgraduate Diploma in QA of Prepreg/Autoclave and Rapid Cure — studying from Australia
Australia no longer manufactures passenger vehicles at scale, but automotive engineering remains significant through component suppliers, design and engineering services, fleet operations and a strong motorsport culture. Engineers contribute to vehicle testing, powertrain development, vehicle dynamics and aftermarket product development. Motorsport activity centres on categories such as Supercars, which draws engineering talent from across the country. Employers include major global suppliers, dealership groups, fleet operators and specialist engineering consultancies working with manufacturers.
Fees for Australia: A$1,420 (AUD), with instalments and employer sponsorship available.
Relevant bodies in Australia
Typical roles
Questions from Australia
Which Australian bodies matter for automotive engineering recognition?
Engineers Australia is the main professional body for engineers and sets the standards for Chartered Professional Engineer status, which generally requires an accredited qualification. Automotive standards in Australia are overseen by bodies such as the Department of Infrastructure and vehicle compliance agencies. SEIUM's private qualifications are not accredited by these bodies, so their value depends on employer assessment.
What automotive careers and employers in Australia could this support?
Australia has automotive suppliers, vehicle engineering firms, motorsport teams and fleet operators, along with a growing mobility sector. Employers typically look at demonstrated technical skills, project work and experience. A SEIUM qualification may support your application, but whether it is recognised is for each employer to decide.
Can I manage this online course alongside a full-time job in Australia?
Yes, the courses are 100% online and taught in English, so you can study around work and from home without a student visa. Specialist courses take 300 hours, postgraduate diplomas 800 hours and master's 1,900 hours. Each student has an assigned technical tutor, and employer-funded training may be possible in some cases.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Handle prepregs in accordance with shelf life and environmental conditions.
Define autoclave cycles with pressure and temperature control.
Interpret cure kinetics through thermal testing.
Evaluate rapid cure and out-of-autoclave processes.
Design quality control plans with witness coupons.
Apply aerospace quality requirements to special processes.
Analyse root causes of curing defects.
Who it's for
- Composites process engineer looking to specialise in QA of Prepreg/Autoclave and Rapid Cure.
- Quality manager looking to specialise in QA of Prepreg/Autoclave and Rapid Cure.
- Autoclave technician looking to specialise in QA of Prepreg/Autoclave and Rapid Cure.
- Materials engineer looking to specialise in QA of Prepreg/Autoclave and Rapid Cure.
- Test laboratory technician looking to specialise in QA of Prepreg/Autoclave and Rapid Cure.
- Special processes auditor looking to specialise in QA of Prepreg/Autoclave and Rapid Cure.
- Graduates in engineering or science seeking to enter a competitive job market.
What you'll work with
- AS9100D aerospace quality management
- SAE AMS 2750 pyrometry
- Nadcap AC7118 composite materials processes
- ASTM D2344 interlaminar shear
- ASTM D7028 Tg by DMA
- ASTM D3171 fibre content
- ASTM E1356 Tg by DSC
- ASTM D2734 void content
8 modules · 800 h
1.1Composition of a prepreg1.2Resin content and areal weight1.3Freezer life and out-time1.4Thawing and moisture control1.5Clean room and environmental conditions1.6Automated cutting and nesting1.7Roll traceability1.8Tack and drapability1.9Defects in incoming material1.10Workshop: incoming quality control of a prepreg roll
2.1How an autoclave works2.2Vacuum bag and consumables2.3Pressure and temperature cycles2.4Thermocouples and part monitoring2.5Cure ramps and dwells2.6Gelation and consolidation2.7Porosity and its control2.8Tooling and thermal expansion2.9Autoclave safety2.10Practical: defining a standard cure cycle
3.1Chemistry of epoxy curing3.2Degree of cure and vitrification3.3Differential scanning calorimetry (DSC)3.4Kamal kinetic models3.5Viscosity during the cycle3.6Glass transition temperature3.7Post-cure and thermal stability3.8Exotherm in thick laminates3.9Cure simulation3.10Laboratory: DSC analysis of a resin
4.1Snap-cure rapid-cure resins4.2Compression moulding of prepreg4.3Out-of-autoclave curing processes4.4Vacuum-only curing prepregs4.5Induction heating and heated moulds4.6Exotherm control in short cycles4.7Properties compared with standard cure4.8Productivity and cost4.9Applications in rapid spare parts4.10Case study: reducing the cycle of a deflector
5.1Process control plan5.2Autoclave cycle records5.3Witness coupons per cycle5.4Interlaminar shear tests5.5Fibre content and porosity5.6Tg by DMA5.7Ultrasonic inspection5.8Non-conformities and concessions5.9Thermocouple calibration5.10Practical: analysis of witness coupons from a batch
6.1AS9100 requirements6.2Nadcap accreditation for composites6.3Pyrometry to AMS 27506.4Qualification of special processes6.5Process audits6.6Document management6.7Training control6.8Quality indicators6.9Material supplier management6.10Case study: audit of an autoclave cycle
7.1Porosity and voids7.2Wrinkles and fibre waviness7.3Debonding and delamination7.4Resin-rich areas7.5Ply misalignment7.6Contamination by release agents7.7Root cause of curing defects7.8Corrective actions and their verification7.9Prevention through design7.10Workshop: root cause analysis of excessive porosity
8.1Selection of part and material8.2Definition of cure cycle8.3Quality control plan8.4Selection of verification tests8.5Rapid cycle proposal8.6Comparison of expected properties8.7Process risk analysis8.8Special process documentation8.9Report and presentation8.10Final review with tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetable: students progress at their own pace within the intake, making it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is Ansys Composite Cure Simulation, Fibersim, TA Instruments TRIOS, Minitab, SAP QM, in free, academic or evaluation versions. Tests are studied using real procedures for autoclave cycle control, witness coupon testing and rapid cure development. Assessment is continuous, per module, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Handle prepregs in accordance with shelf life and environmental conditions.
Define autoclave cycles with pressure and temperature control.
Interpret cure kinetics through thermal testing.
Evaluate rapid cure and out-of-autoclave processes.
Design quality control plans with witness coupons.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours spread over 6 to 8 months. That is between 10 and 15 hours a week on average, compatible with a full-time job.
The programme uses Ansys Composite Cure Simulation, Fibersim, TA Instruments TRIOS, Minitab, SAP QM. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM's own diploma upon passing the continuous assessment and the integrating project. It is in-house training, not an official Ministry qualification.
Yes. Modules passed in a course or postgraduate diploma in the same area can be credited towards the higher programme. Check the credit transfer policy when you enrol.
Related programmes
Postgraduate Diploma in DIL Correlation and Driver Parameterisation
Online 800-hour Postgraduate Diploma in DIL Correlation and Driver Parameterisation. 8 modules covering ISO 8855:2011 vehicle dynamics, vocabulary, SAE J2944 driving performance measures and VI-grade DiM…
Postgraduate Diploma in Renewables and BESS Integration
The Diploma in Integration with Renewables and BESS explores the synergy between renewable energy, especially solar photovoltaic and wind power, and battery energy storage systems (BESS).…
Postgraduate Diploma in Semi-Active and Predictive Damper Control
Online Postgraduate Diploma of 800 hours in Semi-Active and Predictive Damper Control. 8 modules covering ISO 26262, ISO 2631-1 and MATLAB/Simulink. Assigned tutor and open enrolment.
More in Automotive & Motorsport
All Automotive & Motorsport programmes → · How to apply · Fees & financing · Scholarships