Postgraduate Diploma in Waterproofing, IP Ratings and Marine EMC
Online 800-hour Postgraduate Diploma in Waterproofing, IP Ratings and Marine EMC. 8 modules covering IEC 60529 (IP protection degrees), IEC 60945 (marine navigation and radiocommunication equipment) and ANSYS HFSS. Assigned tutor and open enrolment.
Postgraduate Diploma in Waterproofing, IP Ratings and Marine EMC — studying from South Africa
South Africa's coastline and ports make maritime engineering important, with the Port of Durban, the Port of Cape Town and the Port of Ngqura serving major trade flows. The South African Navy and Armscor support naval procurement, and shipbuilding and repair businesses operate along the coast. Offshore energy and marine services create additional demand, and the sports nautical sector serves recreational boating. The South African Maritime Safety Authority regulates shipping and marine safety.
Fees for South Africa: R 16 700 (South African rand), with instalments and employer sponsorship available.
Relevant bodies in South Africa
Typical roles
Questions from South Africa
Will a SEIUM qualification be recognised by the professional bodies in South Africa for this area?
SEIUM qualifications are private, not official state degrees, and are not accredited by any South African body. Marine and offshore work may involve bodies such as the South African Maritime Safety Authority (SAMSA) and ECSA for engineering registration. Recognition of a private qualification is decided by employers or the relevant body, so confirm this with them directly.
How might this qualification be used by employers in South Africa in naval and offshore industries?
Shipyards, offshore energy firms and marine design consultancies look mainly for certified competence, relevant experience and regulatory knowledge. A private qualification may complement these but will not replace formal certification. Its usefulness depends on each employer's assessment, so ask prospective employers how they would weigh it.
Can I study this programme alongside full-time work from South Africa, and is there a time zone or language issue?
Yes, the programme is 100% online and in English, so you can study from home without a student visa. Master's programmes total 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. You receive an assigned technical tutor, can pay in instalments, and may seek employer sponsorship. Confirm time-zone and workload expectations with SEIUM before committing.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Characterise the marine environment and its effects on electronic equipment.
Interpret and specify IP protection degrees according to IEC 60529.
Design watertight, corrosion-resistant enclosures and connections.
Plan environmental tests in accordance with IEC 60068 and IEC 60945.
Apply electromagnetic compatibility design techniques on board.
Carry out electrical installations that preserve watertightness and EMC.
Diagnose equipment failures caused by humidity, corrosion or interference.
Who it's for
- Marine electronics engineer who wants to specialise in Waterproofing, IP Ratings and Marine EMC.
- EMC test engineer who wants to specialise in Waterproofing, IP Ratings and Marine EMC.
- Product regulatory compliance engineer who wants to specialise in Waterproofing, IP Ratings and Marine EMC.
- Watertight enclosure designer who wants to specialise in Waterproofing, IP Ratings and Marine EMC.
- Environmental test laboratory technician who wants to specialise in Waterproofing, IP Ratings and Marine EMC.
- Marine electrical installation engineer who wants to specialise in Waterproofing, IP Ratings and Marine EMC.
- Graduates in engineering or sciences seeking to join marine electronics manufacturers.
What you'll work with
- IEC 60529 (IP protection degrees)
- IEC 60945 (marine navigation and radiocommunication equipment)
- IEC 60533 (electromagnetic compatibility on ships)
- IEC 60068-2 series (environmental testing)
- IACS UR E10 (type approval testing of equipment)
- Directive 2014/30/EU (electromagnetic compatibility)
- Directive 2014/90/EU (marine equipment)
8 modules · 800 h
1.1Aggressiveness of the marine environment towards electronics1.2Salt fog, humidity and condensation1.3UV radiation and thermal cycling1.4Vibration and shock on vessels1.5Installation zones: exposed, protected and bilge1.6Failure mechanisms of marine equipment1.7Galvanic action and connector corrosion1.8Manufacturer and owner requirements1.9Reliability and field failure rates1.10Practice: failure analysis of deck electronics
2.1IEC 60529 standard and the IP code2.2Protection against solids: first digit2.3Protection against water: second digit2.4Differences between IPX6, IPX7 and IPX82.5IK code for impact resistance per IEC 622622.6IP69K ratings for pressure washing2.7Jet and immersion testing2.8Interpreting datasheets2.9Common errors in IP specification2.10Workshop: selecting the IP rating by installation zone
3.1Enclosures and resistant materials3.2O-rings and flat gaskets: design and compression3.3Cable glands and watertight bulkhead fittings3.4Watertight connectors and their assembly3.5Vent membranes and pressure compensation3.6Potting and conformal coatings3.7Management of internal condensation3.8Design of sealed keypads and displays3.9Watertightness verification in production3.10Practice: design of an IP67 enclosure for a deck sensor
4.1IEC 60945 standard for navigation equipment4.2Dry and damp heat testing4.3Salt mist test IEC 60068-2-524.4Vibration and shock testing4.5Solar radiation test4.6Watertightness and immersion tests4.7Accredited and certified laboratories4.8Planning a test campaign4.9Analysis of results and non-conformities4.10Laboratory: environmental test plan for a multifunction display
5.1Fundamentals of electromagnetic interference5.2Conducted and radiated emissions5.3Immunity to surges and transients5.4EMC requirements of IEC 609455.5Directive 2014/53/EU on radio equipment5.6Safe distance from the magnetic compass5.7Interference with VHF, radar and GNSS5.8Noise from engines, inverters and chargers5.9EMC testing in chamber and in the field5.10Case study: interference diagnosis on a yacht's VHF
6.1Standards ISO 13297 and ISO 101336.2ABYC E-11 recommendations6.3Earthing and equipotential bonding6.4Galvanic isolation and transformers6.5Marine cabling and cross-sections6.6Cable routing and signal separation6.7Shielding and filters6.8NMEA 2000 networks and their installation6.9Lithium batteries and protection6.10Practice: electronics installation diagram for a sailing yacht
7.1Periodic connector inspection7.2Insulation measurement7.3Leakage current detection7.4Cleaning and protecting contacts7.5Replacing gaskets and seals7.6NMEA 2000 network diagnostics7.7Marine measuring tools7.8Fault logging7.9Repair versus replacement7.10Case study: galvanic corrosion caused by current leakage
8.1Definition of the equipment and environment8.2IP rating specification8.3Enclosure design8.4Environmental test plan8.5System EMC analysis8.6On-board installation design8.7Maintenance plan8.8Reliability analysis8.9Report and presentation8.10Final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetables: students progress at their own pace within the intake, making it possible to combine the programme with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software includes ANSYS HFSS, CST Studio Suite, KiCad, LTspice, SolidWorks, in free, academic or evaluation versions. Tests are studied using real procedures for salt mist and damp heat chambers, IP watertightness testing with jets and immersion, and EMC emissions and immunity measurements. Assessment is continuous by module, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Characterise the marine environment and its effects on electronic equipment.
Interpret and specify IP protection degrees according to IEC 60529.
Design watertight, corrosion-resistant enclosures and connections.
Plan environmental tests in accordance with IEC 60068 and IEC 60945.
Apply electromagnetic compatibility design techniques on board.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient proficiency in Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 800 hours in total, spread over 6 to 8 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
The programme works with ANSYS HFSS, CST Studio Suite, KiCad, LTspice and SolidWorks. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM own diploma upon passing the continuous assessment and the integrating project. This is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or diploma in the same area can be credited towards the advanced programme. Please check the credit transfer policy when you enrol.
Related programmes
Postgraduate Diploma in Planing Craft Hydrodynamics and Slamming
Online 800-hour Postgraduate Diploma in Planing Craft Hydrodynamics and Slamming. 8 modules covering ISO 12215-5 (design pressures and scantlings for small craft), HSC Code 2000 and…
Postgraduate Diploma in Yard Logistics and Inventory Control
Online 800-hour Postgraduate Diploma in Yard Logistics and Inventory Control. 8 modules covering ISO 9001 (quality management), ISO 28000 (supply chain security) and SAP EWM. Assigned…
Postgraduate Diploma in Flow Integrity and Corrosion Management
Online 800-hour Postgraduate Diploma in Flow Integrity and Corrosion Management. 8 modules covering NORSOK M-001 (materials selection), NORSOK M-506 (CO₂ corrosion model) and OLGA (SLB). Dedicated…
More in Naval, Offshore & Sports Nautical
All Naval, Offshore & Sports Nautical programmes → · How to apply · Fees & financing · Scholarships