Forced Induction in Off-Road Engines Course
Online 300-hour course in forced induction for off-road engines. 6 modules covering Regulation (EU) 2016/1628 (emissions from non-road mobile machinery engines), ISO 8178 (measurement of emissions from reciprocating internal combustion engines) and GT-SUITE. Assigned tutor and open enrolment.
Forced Induction in Off-Road Engines Course — studying from South Africa
Mining, agriculture and construction make off-road and specialised machinery central to South Africa's economy. Mining equipment manufacturers and service providers support the country's extensive gold, platinum and coal operations, while agricultural machinery serves commercial farming. Engineers working on heavy vehicles and special machines focus on hydraulics, drivetrains and durability under harsh conditions. The South African Bureau of Standards and the Mine Health and Safety Council set relevant standards and safety requirements.
Fees for South Africa: R 10 200 (South African rand), with instalments and employer sponsorship available.
Relevant bodies in South Africa
Typical roles
Questions from South Africa
Will a SEIUM qualification be recognised by the professional bodies in South Africa for this area?
SEIUM qualifications are private and not accredited by any South African body. Engineering registration is handled by ECSA, and machinery safety standards are linked to SABS and the Department of Employment and Labour's regulations. Recognition of a private qualification is decided by employers or the relevant body, so confirm this with them before you enrol.
How might this qualification be used by employers in South Africa in off-road and special vehicles?
Mining, agriculture, construction and vehicle-conversion firms value practical machinery knowledge and proven problem-solving. A private qualification can support your application, especially with hands-on experience, but it carries no official status. Its weight depends on each employer, so ask potential employers in your field how they would view it.
Can I study this programme alongside full-time work from South Africa, and is there a time zone or language issue?
The programme is 100% online and in English, so you can study from home without a student visa. Master's programmes take 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. Each student has an assigned technical tutor, fees can be paid in instalments, and employer sponsorship is possible. Check time-zone and workload expectations with SEIUM directly.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the objectives and limits of forced induction in off-road engines.
Compare fixed-geometry, variable-geometry and two-stage turbochargers, as well as mechanical superchargers.
Calculate the matching of turbocharger and engine using compressor maps.
Analyse the relationship between forced induction, emissions and aftertreatment systems.
Identify turbocharger failure modes and their preventive maintenance.
Assess the legality and consequences of forced induction modifications.
Develop a forced induction adaptation project for an engine.
Who it's for
- Engine engineer looking to specialise in Forced Induction in Off-Road Engines.
- Calibration engineer looking to specialise in Forced Induction in Off-Road Engines.
- Diesel engine diagnostics technician looking to specialise in Forced Induction in Off-Road Engines.
- Turbocharger specialist looking to specialise in Forced Induction in Off-Road Engines.
- Heavy-duty engine mechanic looking to specialise in Forced Induction in Off-Road Engines.
- Emissions engineer looking to specialise in Forced Induction in Off-Road Engines.
- Graduates in engineering or science seeking to join engine manufacturers.
What you'll work with
- Regulation (EU) 2016/1628 (emissions from non-road mobile machinery engines)
- ISO 8178 (measurement of emissions from reciprocating internal combustion engines)
- ISO 14396 (power of engines for non-road mobile machinery)
- SAE J1826 (turbocharger gas stand test code)
- SAE J922 (turbocharger nomenclature)
- UNECE Regulation No. 85 (measurement of net power)
- Royal Decree 866/2010 (vehicle modifications)
6 modules · 300 h
1.1Why supercharge a machinery engine1.2Relationship between available air and torque1.3Pressure, temperature and air density1.4Mechanical and thermal limits of the engine1.5Response requirements in machinery1.6Operation at constant speed and at variable load1.7Effect of altitude on forced induction1.8Relationship with emissions standards1.9Terminology and key parameters1.10Workshop: analysis of an engine's requirements
2.1Fixed and variable geometry turbochargers2.2Two-stage turbocharging in series and in parallel2.3Variable geometry turbocharger and its control2.4Mechanical supercharger and its application2.5Turbocompounding and energy recovery2.6Exhaust gas recirculation and its interaction2.7Wastegate and blow-off valves2.8Air-to-air and air-to-water intercoolers2.9Selecting an architecture by application2.10Practical: comparison of two architectures
3.1Air flow required by the engine3.2Compressor selection using its map3.3Turbine selection and ratio3.4Surge and overspeed margin3.5Pressure losses in intake and exhaust3.6Intercooler sizing3.7Adaptation to different operating speeds3.8Bench verification3.9Electronic control tuning3.10Practical: turbocharger selection using maps
4.1Boost pressure control strategies4.2Interaction with injection and timing advance4.3Exhaust gas recirculation control4.4Exhaust temperatures and their management4.5Relationship with the diesel particulate filter4.6Relationship with selective catalytic reduction4.7On-board diagnostics of forced induction4.8Overpressure protection4.9Limp-home modes4.10Practical: analysis of a control strategy
5.1Causes of failure in the forced induction system5.2Lubrication and its criticality5.3Air filtration and particle damage5.4Intake and exhaust leaks5.5Dirt and soot in variable geometry5.6Intercooler blockage and leaks5.7Periodic system inspection5.8Diagnosing loss of performance5.9Intervals and good practice5.10Practical: system maintenance plan
6.1Power increase and its risks6.2Pressure modification and its consequences6.3Effect on warranty and emissions6.4Legality of modifications6.5Reprogramming and its detection6.6Verification after a modification6.7Cases of failure after tampering6.8Common errors in adaptation6.9Trends in forced induction6.10Final project: forced induction specification for an engine
How you'll learn
Fully 100 % online training on the SEIUM Institute campus, with downloadable material, recorded lectures and an assigned technical tutor. There are no fixed timetables: students progress at their own pace within the intake, which makes it compatible with work.
Each module combines theory, guided reading of the original standard and applied exercises. The software used is GT-SUITE, AVL BOOST, Ricardo WAVE, MATLAB, in free, academic or evaluation versions. Tests are studied using real engine test bench procedures, measurement of boost pressure and temperatures, and turbocharger diagnostics. Assessment is continuous by module, plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the objectives and limits of forced induction in off-road engines.
Compare fixed-geometry, variable-geometry and two-stage turbochargers, as well as mechanical superchargers.
Calculate the matching of turbocharger and engine using compressor maps.
Analyse the relationship between forced induction, emissions and aftertreatment systems.
Identify turbocharger failure modes and their preventive maintenance.
Where this takes you
Requirements
- No prior degree required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical regulatory reading.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 300 hours in total, spread over 3 to 5 months. That is between 10 and 15 hours per week on average, compatible with a full-time job.
The course uses GT-SUITE, AVL BOOST, Ricardo WAVE and MATLAB. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM Institute own diploma upon passing the continuous assessment and the integrative project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are credited towards the advanced programme. Check the credit transfer policy when you enrol.
Related programmes
Course in Traction Batteries for Heavy Machinery
Online 300-hour course in traction batteries for heavy machinery. 6 modules covering Regulation (EU) 2023/1542 (batteries and waste batteries), IEC 62619 (safety of lithium batteries for…
Course in Remote Diagnostics for Agricultural Machinery
Online 300 h course in remote diagnostics for agricultural machinery. 6 modules covering ISO 11783 (ISOBUS: communication in tractors and agricultural machinery), SAE J1939 (CAN network…
Safe Machinery Cab Design Course
Online 300-hour course in safe machinery cab design. 6 modules covering ISO 3471 (ROPS in earthmoving machinery), ISO 5006 (operator field of view) and Siemens Tecnomatix…
More in Off-Road, Special Vehicles & Machinery
All Off-Road, Special Vehicles & Machinery programmes → · How to apply · Fees & financing · Scholarships