Diploma in Nuclear Component Integrity Assessment
Online postgraduate diploma of 800 hours in nuclear component integrity assessment. 8 modules covering components and degradation mechanisms, fracture mechanics, non-destructive testing, design and assessment codes, advanced structural analysis, ageing management, and probabilistic approaches and regulation, with an assigned technical tutor.
Diploma in Nuclear Component Integrity Assessment — studying from Singapore
Singapore maintains a comprehensive defence sector through the Ministry of Defence and the Defence Science and Technology Agency, which develops military technologies and manages procurement. Engineering work covers land systems, ammunition, command and control, and simulation. Industry partners include ST Engineering, which supplies defence and security systems globally. Engineers here work within strict security and export control frameworks, often combining systems integration with reliability and safety engineering.
Fees for Singapore: S$1,840 (Singapore dollar), with instalments and employer sponsorship available.
Relevant bodies in Singapore
Typical roles
Questions from Singapore
How does defence engineering work in Singapore, and which bodies oversee it?
Singapore's defence engineering is largely centred on the Ministry of Defence (MINDEF) and DSTA, the defence procurement and development agency, along with the Singapore Armed Forces. Engineers may register with the Professional Engineers Board (PEB). SEIUM's qualifications are private, not state degrees, and not accredited by any national body, so recognition for defence roles depends on the employer or relevant authority.
Who employs defence and land systems engineers in Singapore?
Main employers include MINDEF, DSTA, the SAF, and defence industry companies including ST Engineering. Access to many roles requires security clearance and citizenship or residency rules, so check eligibility early. Employers focus on proven competence and clearance status. Your final project can illustrate technical capability, but it does not replace these requirements.
Is the course manageable alongside a job, and can employers fund it?
The programme is fully online and taught in English, with an assigned technical tutor. Plan for a heavy workload: 1,900 hours for a master's, 800 for a postgraduate diploma, or 300 for a specialist course. Fees are payable in instalments, and employer sponsorship is possible, which is common in defence-linked organisations, though approval is up to them.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Identify the degradation mechanisms of nuclear components.
Apply fracture mechanics to flaw assessment.
Select qualified non-destructive testing techniques.
Interpret the ASME and RCC-M assessment codes.
Carry out structural analyses of pressure components.
Plan ageing management programmes.
Integrate probabilistic approaches into integrity assessment.
Who it's for
- Structural integrity engineers.
- Non-destructive testing specialists moving into nuclear applications.
- Fracture mechanics analysts.
- Ageing management engineers.
- Nuclear component inspectors.
- Licensing technicians.
- Engineering or science graduates seeking to enter the nuclear energy sector.
What you'll work with
- ASME BPVC Section XI (in-service inspection of nuclear components)
- ASME BPVC Section III (nuclear power plant components)
- 10 CFR 50 Appendix G (fracture toughness requirements)
- RCC-M (design and construction rules for mechanical components)
- IAEA SSG-48 (ageing management)
- ISO 9712 (qualification of NDT personnel)
- CSN Instruction IS-22 (Spanish regulatory requirements on ageing management)
- ANSYS Mechanical
- Abaqus
- FAVOR
- Code_Aster
- CIVA
8 modules
1.1The reactor pressure vessel and its internals1.2Piping and steam generators1.3Neutron irradiation embrittlement1.4Stress corrosion cracking1.5Thermal and mechanical fatigue1.6Flow-accelerated corrosion1.7Ageing of concrete1.8Degradation of cables and elastomers1.9Surveillance programmes1.10Case study: degradation of vessel head penetrations
2.1Linear elastic fracture mechanics2.2Stress intensity factor2.3Elastic-plastic fracture mechanics2.4J-integral and CTOD2.5Master Curve for fracture toughness2.6Fatigue crack growth2.7FAD diagrams2.8RTNDT reference temperature2.9Pressurised thermal shock2.10Practical: flaw assessment with an FAD diagram
3.1Conventional ultrasonics3.2Phased array and TOFD3.3Eddy current testing of tubes3.4Industrial radiography3.5Liquid penetrants and magnetic particles3.6ENIQ procedure qualification3.7ISO 9712 personnel certification3.8Remote and robotic inspection3.9Inspection reliability (POD)3.10Laboratory: flaw detection with phased array
4.1ASME Section III4.2ASME Section XI4.3RCC-M and RSE-M4.4Component safety classes4.5Fitness-for-service assessment4.6Flaw acceptance limits4.7Stress analysis4.8In-service inspection requirements4.9Comparison between codes4.10Case study: assessment of an indication under ASME XI
5.1Finite elements applied to components5.2Thermal transients5.3Cumulative fatigue analysis5.4Welding residual stresses5.5Seismic analysis5.6Integrity of supports5.7Fluid-structure interaction5.8Model validation5.9Quality assurance of calculations5.10Practical: thermal analysis of a nozzle
6.1Ageing management programmes6.2NRC GALL report6.3Long-term operation6.4Periodic safety review6.5Materials surveillance with specimens6.6Replacement and repair6.7Condition indicators6.8CSN requirements6.9International operating experience6.10Case study: long-term operation plan
7.1Probabilistic fracture mechanics7.2Risk-informed inspection7.3xLPR and FAVOR codes7.4Uncertainty analysis7.5Integration with PSA7.6Licensing of changes7.7Transparency and communication7.8Ethics of safety assessment7.9Regulatory independence7.10Case study: risk-informed inspection of piping
8.1Selection of the component8.2Degradation mechanisms8.3Inspection plan8.4Flaw characterisation8.5Integrity assessment8.6Remaining life estimate8.7Management recommendations8.8Regulatory discussion8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
A 100% online programme on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so it can be combined with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is ANSYS Mechanical, Abaqus, FAVOR, Code_Aster and CIVA, in free, academic or evaluation versions. Testing is studied through real procedures for phased array ultrasonic inspection, flaw assessment using FAD diagrams and thermal analysis of pressure components. Assessment is continuous by module plus the final integrating project.
Standards covered: ASME BPVC Section XI, ASME BPVC Section III, 10 CFR 50 Appendix G, RCC-M, IAEA SSG-48, ISO 9712, CSN Instruction IS-22.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with ANSYS Mechanical, Abaqus, FAVOR, Code_Aster and CIVA, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in Procurement Processes and Transparency
Online postgraduate diploma of 800 hours in defence procurement processes and transparency. 8 modules covering the legal framework, planning and requirements, transparency, integrity and anti-corruption, international…
Diploma in COMSEC for NATO Platforms
Online postgraduate diploma of 800 hours in COMSEC for NATO platforms, structured in 8 modules covering communications security on platforms, the NATO and national regulatory framework,…
Diploma in Fatigue Testing of Military Transmissions
600-hour online postgraduate diploma in fatigue testing of military transmissions: cumulative damage, rainflow spectra, closed-loop rigs, failure analysis, ISO 6336 and qualification, with an assigned tutor.
More in Defense, Military Engineering & Land Systems
All Defense, Military Engineering & Land Systems programmes → · How to apply · Fees & financing · Scholarships