Postgraduate Diploma in 2T/4T Calibration and Ignition Management
Online 800-hour postgraduate diploma in 2T/4T calibration and ignition management. 8 modules covering ISO 4106, Commission Delegated Regulation (EU) No 134/2014 and ETAS INCA. Assigned tutor and open enrolment.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Analyse the working cycles of two-stroke and four-stroke engines.
Understand how current ignition systems work.
Determine the optimum advance and the limits imposed by knock.
Construct injection and ignition maps using calibration tools.
Calibrate the engine for starting, idle, transients and riding modes.
Integrate emissions and type-approval requirements into calibration.
Develop a complete base calibration from bench tests.
Who it's for
- Engine calibration engineer wishing to specialise in 2T/4T Calibration and Ignition Management.
- Test bench engineer wishing to specialise in 2T/4T Calibration and Ignition Management.
- Engine development engineer wishing to specialise in 2T/4T Calibration and Ignition Management.
- Race preparation technician wishing to specialise in 2T/4T Calibration and Ignition Management.
- Emissions engineer wishing to specialise in 2T/4T Calibration and Ignition Management.
- Engine electronics specialist wishing to specialise in 2T/4T Calibration and Ignition Management.
- Graduates in engineering or science seeking to enter the motorcycle manufacturing sector.
What you'll work with
- ISO 4106
- Commission Delegated Regulation (EU) No 134/2014
- ASAM MCD-2 MC
- ASAM MCD-1 XCP
- EN 228
- JASO M345
- JASO T903
- ISO 13738
8 modules · 800 h
1.1Real versus ideal Otto cycle1.2Scavenging in two-stroke engines1.3Valve timing diagrams in four-stroke engines1.4Volumetric and trapping efficiency1.5Pumping and friction losses1.6Torque and power curves1.7Influence of speed on cylinder filling1.8Particularities of single-cylinder engines1.9High compression ratio engines1.10Workshop: indicated diagram from in-cylinder pressure
2.1Inductive and CDI ignition2.2Pencil coils and iridium spark plugs2.3Spark energy and charging time2.4Ion sensing in the spark plug2.5Twin-spark ignition2.6Ignition in two-stroke engines2.7Crankshaft and camshaft sensors2.8Misfires and their diagnosis2.9Spark plug heat range and selection2.10Laboratory: measuring spark energy with an oscilloscope
3.1Flame propagation and burning3.2Advance for maximum torque (MBT)3.3Mass fraction burned and CA503.4Cycle-to-cycle variability3.5Knock as the limit of advance3.6Effect of mixture richness on combustion3.7Influence of fuel octane rating3.8Exhaust temperature and thermal protection3.9In-cylinder pressure indication3.10Practice: advance sweep on an engine test bed
4.1Injection maps by speed and throttle opening4.2Speed-density and alpha-N systems4.3Narrowband and wideband lambda sensors4.4Temperature and pressure compensation4.5Enrichment during transients4.6Fuel cut-off on overrun4.7Carburettion and power valves in 2T4.8Variable exhaust valves4.9Dual-injection architectures4.10Case study: injection map for a single-cylinder engine
5.1XCP and CCP protocols5.2A2L files and map structure5.3Dynamometer versus engine test bed5.4Design of experiments in calibration5.5Model-based calibration5.6Data logging and analysis5.7Calibration version control5.8Safety in engine testing5.9Automated calibration with optimisation5.10Practice: calibrating a map with CANape
6.1Cold start and warm-up6.2Idle and air control6.3Ride-by-wire throttle response6.4Riding modes and torque maps6.5Altitude and barometric compensation6.6Use with E10 fuel6.7Driveability and low-speed smoothness6.8Rev and speed limiters6.9Quickshifter and ignition cut calibration6.10Workshop: calibration of power modes
7.1Emissions over the cycle and in calibration7.2Declared power requirements7.3Oil-mix lubrication in two-stroke engines7.4Oil specifications for 2T and 4T7.5Engine durability and calibration7.6Protecting calibration against tampering7.7Technical documentation for type approval7.8Competition versus road use7.9Noise and exhaust limitations7.10Case study: power–emissions trade-off in a 2T
8.1Engine description and objectives8.2Bench test plan8.3Advance and richness sweep8.4Building base maps8.5Transient and start calibration8.6Emissions and consumption verification8.7Analysis of results8.8Final calibration proposal8.9Report and presentation8.10Final review with the tutor
How you'll learn
Fully 100 % online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetable: students progress at their own pace within the intake, which makes it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is ETAS INCA, Vector CANape, AVL CONCERTO, AVL IndiCom, MATLAB Model-Based Calibration Toolbox, in free, academic or evaluation versions. Tests are studied using real procedures: advance and richness sweeps on an engine test bed with pressure indicator, transient calibration on a roller dynamometer, and cold-start verification in a climatic chamber. Assessment is continuous per module, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Analyse the working cycles of two-stroke and four-stroke engines.
Understand how current ignition systems work.
Determine the optimum advance and the limits imposed by knock.
Construct injection and ignition maps using calibration tools.
Calibrate the engine for starting, idle, transients and riding modes.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours spread over 6 to 8 months. That equates to an average of 10 to 15 hours a week, compatible with a full-time job.
The programme works with ETAS INCA, Vector CANape, AVL CONCERTO, AVL IndiCom and MATLAB Model-Based Calibration Toolbox. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
An SEIUM diploma awarded on passing the continuous assessment and the integrating project. It is in-house training, not an official Ministry qualification.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised in the higher programme. Check the recognition policy when you enrol.
Related programmes
Postgraduate Diploma in Guarantee and Network SLA Management
Online 800-hour Postgraduate Diploma in Guarantee and Network SLA Management. 8 modules covering Directive (EU) 2019/771, Royal Legislative Decree 1/2007 (TRLGDCU) and SAP S/4HANA. Assigned tutor…
Postgraduate Diploma in Gaps/Flush and Optical Measurement
Online 800-hour Postgraduate Diploma in Gaps/Flush and Optical Measurement. 8 modules covering ISO 1101:2017, ISO 5459:2011 and ZEISS INSPECT. Assigned tutor and open enrolment.
Postgraduate Diploma in Warranty Analytics and Predictive Maintenance
Online Postgraduate Diploma of 800 hours in Warranty Analytics and Predictive Maintenance. 8 modules with ISO 13374-1:2003, ISO 17359:2018 and Python (pandas, scikit-learn). Assigned tutor and…
More in Motorcycles & 2-Wheelers
All Motorcycles & 2-Wheelers programmes → · How to apply · Fees & financing · Scholarships