Jacket and Monopile Engineering Course
Online 300-hour course in jacket and monopile engineering. 6 modules covering DNV-ST-0126 Support structures for wind turbines, IEC 61400-3-1 Design requirements for fixed offshore wind turbines and Bentley SACS. Assigned tutor and open enrolment.
Jacket and Monopile Engineering Course — studiujesz z Polska
Polski przemysł stoczniowy ma długą tradycję, a stocznie w Gdańsku, Gdyni i Szczecinie budują i remontują jednostki pływające oraz realizują konstrukcje offshore. Rozwija się także sektor offshore wiatrowego na Bałtyku, a nautyka sportowa działa w portach jachtowych i u producentów łodzi. Zapotrzebowanie dotyczy inżynierów konstrukcji okrętowych, specjalistów od elektryki morskiej i nadzoru technicznego.
Opłaty dla Polska: 1 970 zł (złoty polski), z dostępnymi ratami i finansowaniem przez pracodawcę.
Właściwe organy w Polska
Typowe role
Pytania z Polska
Czy ten program uprawnia do pracy na statkach lub platformach w Polsce?
Nie. Uprawnienia morskie w Polsce, takie jak świadectwa marynarskie, wydaje Urząd Morski zgodnie z przepisami i konwencjami międzynarodowymi. Kwalifikacje SEIUM nie są państwowe, nie są akredytowane i nie zastępują tych dokumentów.
Jakie polskie firmy zatrudniają specjalistów od inżynierii morskiej?
W Polsce działają stocznie, biura projektowe jednostek pływających oraz firmy offshore, w tym związane z morską energetyką wiatrową. Uznanie prywatnych kwalifikacji zależy od pracodawcy, który ocenia kompetencje kandydata i zrealizowany projekt końcowy.
Czy mogę się uczyć z dowolnego miejsca i czy pracodawca może sfinansować studia?
Tak, program jest w całości online, więc nie jest potrzebna wiza studencka przy nauce z domu. Opłaty można płacić w ratach, a finansowanie przez pracodawcę bywa możliwe. Warunki warto potwierdzić w szkole.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Select between monopile and jacket according to water depth, soil and wind turbine.
Design piles using p-y and PISA methods based on geotechnical data.
Size a monopile against buckling, natural frequencies and fatigue.
Check tubular jacket joints for strength and fatigue.
Apply DNV, IEC and ISO standards for offshore foundations.
Plan the fabrication, transport and driving of foundations.
Develop the foundation design for an offshore wind turbine.
Who it's for
- Offshore foundations engineer wishing to specialise in Jacket and Monopile Engineering.
- Marine geotechnical engineer wishing to specialise in Jacket and Monopile Engineering.
- Offshore wind structures engineer wishing to specialise in Jacket and Monopile Engineering.
- Heavy steel fabrication engineer wishing to specialise in Jacket and Monopile Engineering.
- Installation engineer wishing to specialise in Jacket and Monopile Engineering.
- Design verifier wishing to specialise in Jacket and Monopile Engineering.
- Graduates in engineering or science seeking to enter offshore wind.
What you'll work with
- DNV-ST-0126 Support structures for wind turbines
- IEC 61400-3-1 Design requirements for fixed offshore wind turbines
- ISO 19902 Fixed steel offshore structures
- DNV-RP-C203 Fatigue design of offshore steel structures
- API RP 2GEO Geotechnical and foundation design considerations
- ISO 19901-4 Geotechnical and foundation design
- EN 1993-1-6 Eurocode 3: Strength and stability of shell structures
- DNV-RP-B401 Cathodic protection design
6 modules · 300 h
1.1Monopiles, jackets, tripods and gravity-based foundations1.2Evolution towards large-diameter monopiles1.3Jackets for substations and platforms1.4Water depth ranges and soil types1.5Transition piece and connection to the tower1.6Wind turbine loads versus waves1.7Fabrication chain and assembly ports1.8Supply cost per installed megawatt1.9Experience in North Sea wind farms1.10Case study: monopile versus jacket at 45 m
2.1Geotechnical campaigns with CPT and boreholes2.2Design parameters in sands and clays2.3Axial capacity of driven piles2.4p-y curves and the PISA method2.5Rotational stiffness and system frequency2.6Cyclic soil degradation2.7Scour and rock armour protection2.8Drivability and refusal analysis2.9Drilled piles and cement grout2.10Laboratory: p-y curves of a monopile
3.1Diameter, wall thickness and taper3.2Local buckling of shells3.3Target frequencies between 1P and 3P3.4Coupled aerodynamic and hydrodynamic loads3.5Integrated time-domain simulation3.6Bolted connection versus grouted connection3.7Weld details and fatigue categories3.8Cathodic protection and internal corrosion3.9Secondary structures and access platforms3.10Workshop: preliminary sizing of a 10 m monopile
4.1Leg and Bracing Geometry4.2K, T, and Tubular Joints4.3Stress Concentration Factors4.4Joint Fatigue Using Efthymiou Equations4.5Interface with the wind turbine tower4.6Pre-piling versus post-piling4.7Grouted connections at the base4.8Jacket Weight Optimization4.9Serial manufacturing and automated welding4.10Practice: Fatigue Check of a K joint
5.1Rolling and welding of shells5.2Dimensional control and non-destructive testing5.3Float-over and deck transport5.4Jack-up and heavy-lift vessels5.5Driving with hydraulic hammer5.6Underwater noise and bubble curtains5.7Vibratory driving and alternative techniques5.8Verticality and installation tolerances5.9Weather windows and operating criteria5.10Case study: installation sequence of a wind farm
6.1Site and metocean data6.2Selection of foundation type6.3Geotechnical pile design6.4Structural sizing of the foundation6.5Fatigue analysis6.6Fabrication and installation plan6.7Cost estimation6.8Project risk register6.9Report and presentation6.10Final review with the tutor
How you'll learn
Fully 100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetable: students progress at their own pace within the intake, which makes it possible to combine with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is Bentley SACS, Plaxis 3D, OpenFAST, DNV Sesam, Abaqus, in free, academic or evaluation versions. The exercises work through real geotechnical design procedures for a monopile, fatigue analysis of tubular joints and pile driving planning. Assessment is continuous per module plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Select between monopile and jacket according to water depth, soil and wind turbine.
Design piles using p-y and PISA methods based on geotechnical data.
Size a monopile against buckling, natural frequencies and fatigue.
Check tubular jacket joints for strength and fatigue.
Apply DNV, IEC and ISO standards for offshore foundations.
Where this takes you
Requirements
- No prior degree required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards reading.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 300 hours in total, spread over 3 to 5 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
You work with Bentley SACS, Plaxis 3D, OpenFAST, DNV Sesam, Abaqus. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
SEIUM's own diploma upon passing the continuous assessment and the integrating project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or Postgraduate Diploma in the same area are credited towards the advanced programme. Check the credit transfer policy when you enrol.