Master’s in Metrology and Quality for Reproductions
Online master's programme of 1,900 hours in metrology and quality for reproduction parts. 12 modules covering metrology fundamentals, dimensional instruments, CMMs, 3D scanning, GD&T, reproduction engineering, statistical process control, quality management, materials testing, supplier inspection and metrology laboratories, with an assigned technical tutor.
Master’s in Metrology and Quality for Reproductions — studying from New Zealand
Vehicle restoration and classic engine work in New Zealand is supported by an active enthusiast community and a well-established network of specialist workshops, particularly around the main centres. Historic vehicle registration and compliance fall under the New Zealand Transport Agency Waka Kotahi, and the Vintage Car Club of New Zealand promotes preservation of historic vehicles. Restoration professionals often combine fabrication, engineering and heritage conservation skills.
Fees for New Zealand: NZ$15,700 (New Zealand dollar), with instalments and employer sponsorship available.
Relevant bodies in New Zealand
Typical roles
Questions from New Zealand
Is restoration engineering recognised by a professional body in New Zealand?
There is no specific statutory register for classic vehicle or heritage restoration engineers in New Zealand. Heritage matters can involve Heritage New Zealand Pouhere Taonga, and vehicle roadworthiness is governed by the NZ Transport Agency Waka Kotahi. SEIUM's qualifications are private and not accredited by any national body, so their value depends on the employer or client.
Where do classic restoration specialists work in New Zealand?
Work is found in independent restoration workshops, classic car dealers, museums, and specialist fabrication businesses, many clustered around the main centres. Clients and employers usually judge by workmanship and a portfolio of completed restorations. A private qualification may complement that evidence but is rarely a deciding factor on its own.
Can I study this while running or working in a workshop here?
Yes. The course is fully online and taught in English, so you can study from home in New Zealand without a student visa. Specialist courses total 300 hours, postgraduate diplomas 800 hours and master's programmes 1,900 hours. An assigned technical tutor supports you, and fees can be paid in instalments.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Apply the fundamentals of metrology and uncertainty calculation.
Use instruments and CMMs for dimensional measurement.
Digitise and compare parts with non-contact technologies.
Specify geometries using GPS and GD&T language.
Design processes for reproducing parts.
Control processes with statistical techniques.
Implement quality systems and accredited laboratories.
Who it's for
- Metrology engineers moving into the reproduction of parts.
- Quality technicians.
- Calibration laboratory managers.
- Reverse engineering engineers.
- Supplier quality inspectors.
- Managers responsible for reproduction parts programmes.
- Engineering or science graduates seeking to enter the spare parts manufacturing sector.
What you'll work with
- ISO/IEC 17025 (competence of testing and calibration laboratories)
- JCGM 100:2008 (Guide to the expression of uncertainty in measurement, GUM)
- ISO 1101 (geometrical product specifications)
- ISO 10360 (acceptance tests for CMMs)
- ISO 9001 (quality management systems)
- IATF 16949 (automotive quality management)
- ISO 14253-1 (decision rules for proving conformity)
- PC-DMIS
- ZEISS Calypso
- PolyWorks
- GOM Inspect
- Minitab
12 modules
1.1International System of Units and measurement standards1.2International Vocabulary of Metrology (VIM)1.3Metrological traceability chain1.4Accuracy, precision and resolution1.5Measurement uncertainty according to the GUM1.6Difference between calibration and verification1.7Accredited and certified laboratories1.8Environmental conditions for measurement1.9Systematic and random errors1.10Laboratory: uncertainty calculation for a micrometer
2.1Callipers, micrometers and dial indicators2.2Gauge blocks and feeler gauges2.3Bore gauges and internal measuring instruments2.4Stylus roughness testers2.5Profile projectors and microscopes2.6Height gauges with probes2.7Thread measurement by the three-wire method2.8Maintenance and care of instruments2.9Management of the measuring equipment fleet2.10Practical: measurement of a period crankshaft
3.1Operating principle of CMMs3.2Probes, heads and stylus qualification3.3Programming measurement routines3.4Alignments and reference systems3.5Evaluation of geometric features3.6CMM verification according to ISO 103603.7Portable measuring arms3.8Measuring large parts with a laser tracker3.9Interpretation of measurement reports3.10Laboratory: programming a CMM
4.1Structured-light scanners4.2Laser line scanners4.3Industrial computed tomography4.4Photogrammetry for large parts4.5Comparison between point cloud and CAD4.6Colour deviation maps4.7Accuracy and limitations of each technology4.8Preparation of shiny surfaces4.9Complete digitisation workflow4.10Practical: comparison of a reproduced part with the original
5.1GPS language according to ISO 11015.2Form tolerances and their verification5.3Orientation and location tolerances5.4Reference systems and datums5.5Maximum material requirement5.6Surface profile tolerances5.7Interpretation of period drawings5.8Translating old drawings into GPS5.9Functional verification with gauges5.10Workshop: GD&T dimensioning of a flange
6.1Definition of a reproduced part6.2Sources: original parts, drawings and archives6.3Dimensional reverse engineering6.4Recovery of original design dimensions6.5Selection of equivalent materials6.6Manufacturing processes for reproductions6.7Functional and aesthetic validation6.8Technical documentation of the reproduction6.9Permissible differences from the original part6.10Case study: reproduction of a chrome trim piece
7.1Variability and special causes7.2Control charts for variables7.3Process capability Cp and Cpk7.4Acceptance sampling plans7.5Measurement system analysis (MSA)7.6Repeatability and reproducibility studies7.7Data analysis with statistical software7.8Data-driven process improvement7.9Statistical control in short runs7.10Practical: R&R study of a gauge
8.1ISO 9001 requirements in practice8.2Advanced product quality planning (APQP)8.3Design and process FMEA8.4Preparing the control plan8.5Part approval through PPAP8.6Management of nonconformities8.7Corrective actions with the 8D methodology8.8Internal audit programme8.9Continuous improvement tools8.10Workshop: process FMEA for a reproduced part
9.1Characterisation of original materials9.2Chemical analysis by spark spectrometry9.3Brinell, Rockwell and Vickers hardness tests9.4Standardised tensile tests9.5Metallographic preparation and microscopy9.6Coating adhesion tests9.7Accelerated ageing tests9.8Equivalences between material standards9.9Supplier material certificates9.10Laboratory: analysis of a period alloy
10.1Incoming inspection plans10.2Initial supplier evaluation10.3First article inspection10.4Process audits at suppliers10.5Technical purchasing specifications10.6Batch management and identification10.7Traceability of materials and parts10.8Communication of quality requirements10.9Supplier performance indicators10.10Case study: first article inspection
11.1Laboratory design and layout11.2Environmental control of temperature and humidity11.3Accreditation according to ISO/IEC 1702511.4Validation of measurement methods11.5Internal calibration programme11.6Participation in interlaboratory comparisons11.7Laboratory technical documentation11.8Competence of technical staff11.9Issuing calibration reports11.10Practical: internal calibration procedure
12.1Selection of the reproduction part12.2Metrological analysis of the original part12.3Complete geometric specification12.4Manufacturing plan for the reproduction12.5Control and metrology plan12.6Statistical study of the process12.7Design of the quality system12.8Final validation of the reproduction12.9Thesis report12.10Master's Thesis: defence before a panel
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so the programme fits around your work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is PC-DMIS, ZEISS Calypso, PolyWorks, GOM Inspect and Minitab, in free, academic or evaluation versions. Testing is studied through real procedures for measuring parts on CMMs, comparing scans with CAD models and R&R studies of measurement systems. Assessment is continuous by module, plus the final Master's Thesis.
Standards covered: ISO/IEC 17025, JCGM 100:2008 (GUM), ISO 1101, ISO 10360, ISO 9001, IATF 16949 and ISO 14253-1.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- A university degree in engineering, science or architecture, or equivalent demonstrable professional experience.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 1,900 hours over 12–14 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with PC-DMIS, ZEISS Calypso, PolyWorks, GOM Inspect and Minitab, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the Master's Thesis. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised in the higher programme. Ask about the recognition policy when you enrol.
A university degree in engineering, science or architecture, or equivalent demonstrable professional experience.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Master’s in Chrome Plating, Nickel Plating and Surface Treatments
Online master's programme of 1,900 hours in chrome plating, nickel plating and surface treatments. 12 modules covering applied electrochemistry, part preparation, copper, nickel and decorative chrome…
Master’s in Regularity Rallies and Classic Sports Cars
Online master's programme of 1,900 hours in regularity rallies and classic sports cars. 12 modules covering sporting regulations, navigation and road books, time calculation and control,…
Master’s in Responsible Restoration and Sensitive Materials
Online master's programme of 1,900 hours in responsible restoration and sensitive materials: 12 modules covering hazardous materials in historic vehicles, the legal framework, identification and analysis,…
More in Restoration & Classics
All Restoration & Classics programmes → · How to apply · Fees & financing · Scholarships