Postgraduate Diploma in Extreme Anti-Corrosion and Bodywork Sealing
Online 800-hour Postgraduate Diploma in Extreme Anti-Corrosion and Bodywork Sealing. 8 modules covering ISO 12944 (corrosion protection of steel structures by protective paint systems), ISO 8501-1 (preparation grades of steel substrates) and advanced Excel. Assigned tutor and open enrolment.
Postgraduate Diploma in Extreme Anti-Corrosion and Bodywork Sealing — studying from Malta
Malta's rich heritage, including historic buildings, vintage vehicles and maritime craft, creates a niche for restoration and conservation work. Owners of classic cars, motorcycles and boats seek specialist workshops with knowledge of period engineering and materials. Restoration of historic architecture also requires engineers and technicians familiar with traditional construction methods and conservation rules. Opportunities tend to be found with specialist workshops, heritage organisations and private restorers.
Fees for Malta: €895 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a recognised professional body in Malta for restoration and classic vehicle engineering?
Malta does not have a single state-regulated profession for classic vehicle restoration. Vehicle registration and roadworthiness are handled by Transport Malta. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is determined by employers, clients or the relevant body, so check these before enrolling.
What work could restoration engineers find in Malta?
Malta has a niche market for classic vehicle restoration, mainly through independent workshops, specialist garages and private collectors. Work is often built on reputation and practical craftsmanship. Whether a private online qualification adds value is for individual clients and employers to judge, so it is best to consider it alongside your hands-on experience.
Can I study this part-time with a workshop job, and is funding possible?
Yes. The programmes are fully online, taught in English and suitable for study from home, without needing a student visa. Hours range from 300 to 1,900 depending on the programme. Fees are payable in instalments, employer sponsorship is possible, and each student has an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the corrosion mechanisms affecting steel bodywork.
Select the appropriate surface preparation method for each component.
Specify protection systems according to the corrosivity of the environment.
Apply sealants to joints, overlaps and bodywork connections.
Protect cavities and underbodies with waxes and specific coatings.
Repair corrosion-damaged areas while restoring protection.
Verify the quality of protection through standardised testing.
Who it's for
- Corrosion protection technician for vehicle bodywork who wishes to specialise in Extreme Anti-Corrosion and Bodywork Sealing.
- Panel and paint restorer who wishes to specialise in Extreme Anti-Corrosion and Bodywork Sealing.
- Coatings inspector who wishes to specialise in Extreme Anti-Corrosion and Bodywork Sealing.
- Quality technician in surface treatments who wishes to specialise in Extreme Anti-Corrosion and Bodywork Sealing.
- Bodyshop manager who wishes to specialise in Extreme Anti-Corrosion and Bodywork Sealing.
- Sealant application technician who wishes to specialise in Extreme Anti-Corrosion and Bodywork Sealing.
- Graduates in engineering or science seeking to enter classic vehicle restoration.
What you'll work with
- ISO 12944 (corrosion protection by paint systems)
- ISO 8501-1 (preparation grades of steel substrates)
- ISO 9227 (salt spray testing)
- ISO 9223 (corrosivity of atmospheres)
- ISO 4628 (assessment of degradation of coatings)
- ISO 2409 (cross-cut adhesion test)
- ISO 6270-2 (resistance to humidity by condensation)
8 modules · 800 h
1.1Electrochemistry of steel corrosion1.2Galvanic corrosion between metals1.3Crevice and filiform corrosion1.4Corrosion under paint and blistering1.5Effects of road salts and marine environments1.6ISO 9223 corrosivity categories1.7Critical areas: underbodies, sills and wheel arches1.8Corrosion in aluminium and magnesium1.9Mechanisms in off-road and agricultural vehicles1.10Case study: corrosion diagnosis on a 4×4
2.1ISO 8501-1 rust grades2.2Abrasive blasting and Sa grades2.3Chemical and mechanical pickling2.4Degreasing and control of soluble salts2.5Roughness and anchor profile2.6Treatment of residual rust2.7Phosphating and pretreatments2.8Cathodic electrodeposition2.9Protection of untreated areas2.10Practice: profile measurement and surface cleaning
3.1Epoxy and zinc-rich primers3.2Hot-dip galvanising to ISO 14613.3Thermal spray metallising3.4Paint systems to ISO 129443.5Polyurea coatings3.6Cavity waxes and underbody products3.7Cathodic protection and its limits3.8Compatibility between layers3.9Film thickness and control3.10Laboratory: film thickness measurement
4.1Polyurethane and MS polymer sealants4.2Sealing of welded joints4.3Factory sealing beads4.4Door seals and gaskets4.5Grommets and bodywork plugs4.6Watertightness against water and dust4.7Roof and glass sealing4.8Structural adhesives4.9Ageing of sealants4.10Workshop: joint sealing in wheel arches
5.1Access to closed cavities5.2Wax spraying with probes5.3Cavity drainage and ventilation5.4Bituminous products and anti-gravel coatings5.5Protection of chassis rails5.6Protection of brake and fuel lines5.7Endoscope inspection5.8Periodic maintenance of protection5.9Errors that trap moisture5.10Practice: cavity protection protocol
6.1Assessment of thickness loss6.2Cutting out and replacing panels6.3Welding of patches and panels6.4Protection of repair welds6.5Treatment of interior areas6.6Restoration of watertightness6.7Repair of corroded chassis6.8Structural rejection criteria6.9Repair documentation6.10Case study: repair of a perforated sill
7.1Neutral salt spray ISO 92277.2Cyclic corrosion testing7.3Cross-cut adhesion ISO 24097.4Pull-off adhesion ISO 46247.5Gravel impact testing7.6Visual inspection and rust grades7.7Thickness and porosity measurement7.8Anti-corrosion warranty criteria7.9Quality reports7.10Workshop: inspection plan for a treatment
8.1Vehicle diagnosis8.2Classification of the operating environment8.3Selection of the protection system8.4Surface preparation8.5Sealing and cavity plan8.6Quality control plan8.7Planned maintenance8.8Budget8.9Report and presentation8.10Final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetables: students progress at their own pace within the intake, making it easy to combine with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is advanced Excel, ElcoMaster (Elcometer), Minitab, SolidWorks, in free, academic or evaluation versions. Testing is studied using real procedures for salt spray chambers, film thickness measurement and endoscopic cavity inspection. Assessment is continuous across modules, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the corrosion mechanisms affecting steel bodywork.
Select the appropriate surface preparation method for each component.
Specify protection systems according to the corrosivity of the environment.
Apply sealants to joints, overlaps and bodywork connections.
Protect cavities and underbodies with waxes and specific coatings.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 800 hours in total, spread over 6 to 8 months. That is an average of between 10 and 15 hours per week, compatible with full-time work.
You will work with advanced Excel, ElcoMaster (Elcometer), Minitab and SolidWorks. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM own diploma upon passing the continuous assessment and the integrating project. This is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area can be credited towards the advanced programme. Please check the credit transfer policy when you enrol.
Related programmes
Diploma in Lighting, Tyres and Night/Weather Driving
Online postgraduate diploma of 800 hours in lighting, tyres and night/weather driving. 8 modules covering night and adverse-weather driving, lighting technology and installation, tyres, climate preparation,…
Diploma in Advanced Torque Vectoring in Motorsport
Online postgraduate diploma of 800 hours in advanced torque vectoring in motorsport, structured in 8 modules covering lateral dynamics and torque distribution, vectoring architectures, vehicle state…
Postgraduate Diploma in Fittings: Polishing, Chrome Plating and Fine Adjustment
Online 800-hour Postgraduate Diploma in Fittings: Polishing, Chrome Plating and Fine Adjustment. 8 modules with ISO 1456 (electrolytic nickel and chromium coatings), ISO 2819 (adhesion of…
More in Restoration & Classics
All Restoration & Classics programmes → · How to apply · Fees & financing · Scholarships