Introduction to Nuclear Fission Reactors Course
Online 300-hour course in introduction to nuclear fission reactors. 6 modules covering IAEA SF-1 (Fundamental Safety Principles), the Convention on Nuclear Safety and IAEA Reactor Simulators for PC. Dedicated tutor and open enrolment.
Introduction to Nuclear Fission Reactors Course — studying from Malta
Malta has no nuclear power generation, and its nuclear engineering relevance lies mainly in radiation protection, safeguards awareness, medical and industrial radiation use, and regulatory oversight of radioactive materials. The Malta Radiation Protection Department and the Health Directorate oversee the use of radiation in hospitals, research and industry. Engineers may find roles in medical physics support, radiological monitoring and compliance. The sector is largely confined to applied and regulatory work rather than fuel cycle activity.
Fees for Malta: €644 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a professional route in Malta for nuclear engineering, and is SEIUM's qualification recognised?
Malta does not operate nuclear power plants, so nuclear engineering careers there are limited, and roles are more likely in regulation, consultancy or international work. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is decided by employers or the relevant regulatory body, so verify this before enrolling.
What employment could this training lead to in Malta?
Given Malta has no nuclear power generation, local opportunities are few and would mostly sit within consultancy, international organisations or firms working abroad. Employers in these roles set their own qualification requirements, and a private online qualification may or may not be accepted. Reviewing job requirements and speaking with employers will show how the training would be viewed.
Can I study this from Malta without relocating, and how is the workload structured?
Yes, the programmes are 100% online, taught in English and suitable for study from home, so you do not need a student visa. Master's programmes total 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. Each student has an assigned technical tutor, and fees are payable in instalments, with possible employer sponsorship.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the fundamentals of nuclear physics as applied to fission.
Classify the main types of fission reactors.
Describe the core and its neutronic and thermal behaviour.
Identify the main and auxiliary systems of a power plant.
Understand the principles of safety, operation and regulation.
Interpret the operation of a power plant using a simulator.
Develop an integrative project on a fission power plant.
Who it's for
- Nuclear power plant operations engineer wishing to specialise in Introduction to Nuclear Fission Reactors.
- Control room technician wishing to specialise in Introduction to Nuclear Fission Reactors.
- Nuclear projects engineer wishing to specialise in Introduction to Nuclear Fission Reactors.
- Radiological protection technician wishing to specialise in Introduction to Nuclear Fission Reactors.
- Nuclear maintenance engineer wishing to specialise in Introduction to Nuclear Fission Reactors.
- Energy sector consultant wishing to specialise in Introduction to Nuclear Fission Reactors.
- Graduates in engineering or sciences seeking to enter nuclear power plants.
What you'll work with
- IAEA SF-1 (Fundamental Safety Principles)
- Convention on Nuclear Safety
- Directive 2009/71/Euratom, as amended by 2014/87/Euratom (nuclear safety)
- IAEA SSR-2/1 Rev.1 (Safety of Nuclear Power Plants: Design)
- Law 25/1964 (on Nuclear Energy)
- Royal Decree 1400/2018 (Regulation on Nuclear Safety in Nuclear Installations)
- 10 CFR Part 50 (Licensing of Production and Utilisation Facilities)
6 modules · 300 h
1.1Nuclear structure and binding energy1.2Fission: what happens and how much energy is released1.3Neutrons: production, moderation and absorption1.4Cross section and its energy dependence1.5Fissile materials and fertile materials1.6Chain reaction and multiplication factor1.7Criticality, subcriticality and supercriticality1.8Delayed neutrons: why a reactor can be controlled1.9Fission products and residual heat1.10Exercise: energy balance of a fission
2.1Classification by moderator and coolant2.2Pressurised water reactors2.3Boiling water reactors2.4Heavy water reactors2.5Gas-cooled reactors2.6Fast reactors and liquid metal-cooled reactors2.7Molten salt reactors2.8Small modular reactors2.9Research and isotope production reactors2.10Practice: compare three technologies for the same requirement
3.1Core geometry and fuel arrangement3.2Fuel assemblies and their structure3.3Control rods and neutron poisons3.4Reactivity coefficients and feedback3.5Xenon and samarium poisoning3.6Fuel burn-up and cycle management3.7Power distribution and peaking factors3.8Heat transfer from fuel to coolant3.9Thermal operating limits3.10Practice: analyse the evolution of reactivity over a cycle
4.1Primary and secondary circuits4.2Steam generators and turbine4.3Cooling and ultimate heat sink4.4Containment and confinement barriers4.5Active and passive safety systems4.6Nuclear and process instrumentation4.7Reactor control and protection4.8Power supply and emergency systems4.9Fuel handling and storage4.10Practice: follow the path of energy from start to finish
5.1Defence in depth5.2Design basis accident analysis5.3Severe accidents and their management5.4Lessons learned from historical accidents5.5Safety culture and the human factor5.6Regulatory bodies and licensing process5.7Normal operation, shutdowns and refuelling5.8In-service maintenance and inspection5.9Decommissioning and end of life of the facility5.10Practice: analyse a documented accident sequence
6.1Choice of reactor technology6.2Description of the system and its parameters6.3Fuel cycle analysis6.4Associated safety systems6.5Transient analysis6.6Applicable regulatory framework6.7Management of waste generated6.8Comparison with energy alternatives6.9Technical report6.10Project defence
How you'll learn
Fully 100% online training on the SEIUM campus, with downloadable material, recorded lectures and a dedicated technical tutor. No fixed timetable: students progress at their own pace within the intake, making it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is IAEA Reactor Simulators for PC, Serpent 2, MATLAB, Python (NumPy), in free, academic or evaluation versions. Tests are studied using real power plant simulator procedures for educational purposes, neutron balance calculations and analysis of operating cases. Assessment is continuous per module, plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the fundamentals of nuclear physics as applied to fission.
Classify the main types of fission reactors.
Describe the core and its neutronic and thermal behaviour.
Identify the main and auxiliary systems of a power plant.
Understand the principles of safety, operation and regulation.
Where this takes you
Requirements
- No prior degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical regulatory texts.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 300 hours in total, spread over 3 to 5 months. That is between 10 and 15 hours per week on average, compatible with a full-time job.
The course uses IAEA Reactor Simulators for PC, Serpent 2, MATLAB, Python (NumPy). Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM own diploma upon passing the continuous assessment and the integrative project. This is in-house training, not an official title from the Ministry.
Yes. Modules passed on a course or Postgraduate Diploma in the same area are credited towards the advanced programme. Check the credit transfer policy when you enrol.
Related programmes
Course on Mechanical Properties of UO₂ and MOX
Online 300-hour course on the mechanical properties of UO₂ and MOX. 6 modules covering ASTM C776 (UO₂ sintered pellets), ASTM C833 ((U,Pu)O₂ sintered pellets) and FRAPCON/FRAPTRAN.…
Nuclear Licensing Course: Regulatory Processes
Online 300-hour course in nuclear licensing: regulatory processes. 6 modules covering IAEA SSG-12 (licensing process for nuclear installations), 10 CFR Part 52 (licences, certifications and approvals…
Course on Hybrid Fission-Fusion Power Generation
Online course of 300 h in Hybrid Fission-Fusion Power Generation. 6 modules covering ASME BPVC Section III, Division 4 (fusion energy device components), IAEA SSR-2/1 (Rev.…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships