Forced Induction in Off-Road Engines Course
Online 300-hour course in forced induction for off-road engines. 6 modules covering Regulation (EU) 2016/1628 (emissions from non-road mobile machinery engines), ISO 8178 (measurement of emissions from reciprocating internal combustion engines) and GT-SUITE. Assigned tutor and open enrolment.
Forced Induction in Off-Road Engines Course — studying from Malta
Malta's construction, quarrying and infrastructure activity creates demand for heavy machinery, specialist vehicles and their maintenance. Contractors, plant hire companies and public works departments rely on skilled technicians and engineers to keep equipment safe and productive. The island's rugged terrain and coastal conditions also support niche markets in agricultural and marine-adjacent machinery. Engineers in this area commonly work with equipment dealers, contractors and public authorities responsible for fleet management.
Fees for Malta: €546 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Which Maltese authorities regulate special vehicles and machinery, and does this qualification fit?
Machinery and vehicle safety in Malta follow EU-derived rules, with Transport Malta handling vehicle matters and the Occupational Health and Safety Authority overseeing workplace machinery. SEIUM Institute's qualifications are private and not official state degrees or accredited by a national body. Recognition for regulated roles is for employers or the relevant authority to decide.
Where might off-road and machinery engineers find work in Malta?
Malta's opportunities in this field are mostly in construction, plant hire, equipment maintenance and the marine and industrial services sectors. Employers in these areas usually value hands-on experience highly. How they view a private online qualification is for each employer to decide, so asking them directly is worthwhile.
Is employer funding available, and how demanding is the English language requirement?
Employer sponsorship is possible, and tuition can be paid in instalments. Programmes are taught fully in English, so you should be comfortable with technical English reading and writing. The online format lets you study around work, and each student has an assigned technical tutor. Hours range from 300 to 1,900 depending on the programme chosen.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the objectives and limits of forced induction in off-road engines.
Compare fixed-geometry, variable-geometry and two-stage turbochargers, as well as mechanical superchargers.
Calculate the matching of turbocharger and engine using compressor maps.
Analyse the relationship between forced induction, emissions and aftertreatment systems.
Identify turbocharger failure modes and their preventive maintenance.
Assess the legality and consequences of forced induction modifications.
Develop a forced induction adaptation project for an engine.
Who it's for
- Engine engineer looking to specialise in Forced Induction in Off-Road Engines.
- Calibration engineer looking to specialise in Forced Induction in Off-Road Engines.
- Diesel engine diagnostics technician looking to specialise in Forced Induction in Off-Road Engines.
- Turbocharger specialist looking to specialise in Forced Induction in Off-Road Engines.
- Heavy-duty engine mechanic looking to specialise in Forced Induction in Off-Road Engines.
- Emissions engineer looking to specialise in Forced Induction in Off-Road Engines.
- Graduates in engineering or science seeking to join engine manufacturers.
What you'll work with
- Regulation (EU) 2016/1628 (emissions from non-road mobile machinery engines)
- ISO 8178 (measurement of emissions from reciprocating internal combustion engines)
- ISO 14396 (power of engines for non-road mobile machinery)
- SAE J1826 (turbocharger gas stand test code)
- SAE J922 (turbocharger nomenclature)
- UNECE Regulation No. 85 (measurement of net power)
- Royal Decree 866/2010 (vehicle modifications)
6 modules · 300 h
1.1Why supercharge a machinery engine1.2Relationship between available air and torque1.3Pressure, temperature and air density1.4Mechanical and thermal limits of the engine1.5Response requirements in machinery1.6Operation at constant speed and at variable load1.7Effect of altitude on forced induction1.8Relationship with emissions standards1.9Terminology and key parameters1.10Workshop: analysis of an engine's requirements
2.1Fixed and variable geometry turbochargers2.2Two-stage turbocharging in series and in parallel2.3Variable geometry turbocharger and its control2.4Mechanical supercharger and its application2.5Turbocompounding and energy recovery2.6Exhaust gas recirculation and its interaction2.7Wastegate and blow-off valves2.8Air-to-air and air-to-water intercoolers2.9Selecting an architecture by application2.10Practical: comparison of two architectures
3.1Air flow required by the engine3.2Compressor selection using its map3.3Turbine selection and ratio3.4Surge and overspeed margin3.5Pressure losses in intake and exhaust3.6Intercooler sizing3.7Adaptation to different operating speeds3.8Bench verification3.9Electronic control tuning3.10Practical: turbocharger selection using maps
4.1Boost pressure control strategies4.2Interaction with injection and timing advance4.3Exhaust gas recirculation control4.4Exhaust temperatures and their management4.5Relationship with the diesel particulate filter4.6Relationship with selective catalytic reduction4.7On-board diagnostics of forced induction4.8Overpressure protection4.9Limp-home modes4.10Practical: analysis of a control strategy
5.1Causes of failure in the forced induction system5.2Lubrication and its criticality5.3Air filtration and particle damage5.4Intake and exhaust leaks5.5Dirt and soot in variable geometry5.6Intercooler blockage and leaks5.7Periodic system inspection5.8Diagnosing loss of performance5.9Intervals and good practice5.10Practical: system maintenance plan
6.1Power increase and its risks6.2Pressure modification and its consequences6.3Effect on warranty and emissions6.4Legality of modifications6.5Reprogramming and its detection6.6Verification after a modification6.7Cases of failure after tampering6.8Common errors in adaptation6.9Trends in forced induction6.10Final project: forced induction specification for an engine
How you'll learn
Fully 100 % online training on the SEIUM Institute campus, with downloadable material, recorded lectures and an assigned technical tutor. There are no fixed timetables: students progress at their own pace within the intake, which makes it compatible with work.
Each module combines theory, guided reading of the original standard and applied exercises. The software used is GT-SUITE, AVL BOOST, Ricardo WAVE, MATLAB, in free, academic or evaluation versions. Tests are studied using real engine test bench procedures, measurement of boost pressure and temperatures, and turbocharger diagnostics. Assessment is continuous by module, plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the objectives and limits of forced induction in off-road engines.
Compare fixed-geometry, variable-geometry and two-stage turbochargers, as well as mechanical superchargers.
Calculate the matching of turbocharger and engine using compressor maps.
Analyse the relationship between forced induction, emissions and aftertreatment systems.
Identify turbocharger failure modes and their preventive maintenance.
Where this takes you
Requirements
- No prior degree required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical regulatory reading.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 300 hours in total, spread over 3 to 5 months. That is between 10 and 15 hours per week on average, compatible with a full-time job.
The course uses GT-SUITE, AVL BOOST, Ricardo WAVE and MATLAB. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM Institute own diploma upon passing the continuous assessment and the integrative project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are credited towards the advanced programme. Check the credit transfer policy when you enrol.
Related programmes
Course in Construction Machinery Safety Regulations
Online 300-hour course in construction machinery safety regulations. 6 modules covering Royal Decree 1627/1997 (safety on construction sites), Royal Decree 1215/1997 (work equipment) and AENORmás (standards…
Course in Spare Parts Management for Heavy Machinery
Online course of 300 h in spare parts management for heavy machinery. 6 modules covering EN 13306 (maintenance terminology), ISO 55001 (asset management) and SAP PM/MM.…
Safe Bulldozer Operation Course
Online 300-hour course in safe bulldozer operation. 6 modules covering EN 474-2 (crawler tractors and bulldozers, safety), ISO 6747 (earth-moving tractors, terminology) and Trimble Earthworks. Assigned…
More in Off-Road, Special Vehicles & Machinery
All Off-Road, Special Vehicles & Machinery programmes → · How to apply · Fees & financing · Scholarships