Diploma in FIA Safety Validation and Testing
Online postgraduate diploma of 800 hours in FIA safety validation and testing, with 8 modules covering passive safety, homologated safety equipment, vehicle safety structures, dynamic impact testing, impact simulation, fire and systems testing and laboratory quality, with an assigned technical tutor.
Diploma in FIA Safety Validation and Testing — studying from Malta
Malta's rich heritage, including historic buildings, vintage vehicles and maritime craft, creates a niche for restoration and conservation work. Owners of classic cars, motorcycles and boats seek specialist workshops with knowledge of period engineering and materials. Restoration of historic architecture also requires engineers and technicians familiar with traditional construction methods and conservation rules. Opportunities tend to be found with specialist workshops, heritage organisations and private restorers.
Fees for Malta: €1,290 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a recognised professional body in Malta for restoration and classic vehicle engineering?
Malta does not have a single state-regulated profession for classic vehicle restoration. Vehicle registration and roadworthiness are handled by Transport Malta. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is determined by employers, clients or the relevant body, so check these before enrolling.
What work could restoration engineers find in Malta?
Malta has a niche market for classic vehicle restoration, mainly through independent workshops, specialist garages and private collectors. Work is often built on reputation and practical craftsmanship. Whether a private online qualification adds value is for individual clients and employers to judge, so it is best to consider it alongside your hands-on experience.
Can I study this part-time with a workshop job, and is funding possible?
Yes. The programmes are fully online, taught in English and suitable for study from home, without needing a student visa. Hours range from 300 to 1,900 depending on the programme. Fees are payable in instalments, employer sponsorship is possible, and each student has an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand impact biomechanics and human tolerance.
Know the homologation requirements for safety equipment.
Validate safety structures through calculation and testing.
Prepare and interpret dynamic impact tests.
Simulate impacts using explicit finite elements.
Carry out fire and safety-systems tests.
Apply quality and accreditation criteria in the laboratory.
Who it's for
- Motorsport safety engineers.
- Impact test engineers looking to broaden their expertise in FIA homologation.
- Crash simulation engineers.
- Homologation laboratory technicians.
- Equipment homologation managers.
- Composite structures engineers.
- Engineering or science graduates seeking to enter motorsport.
What you'll work with
- FIA Appendix J, Article 253 (safety equipment)
- FIA Standard 8862-2009 (advanced racing seats)
- FIA Standard 8853-2016 (safety harnesses)
- FIA Standard 8860-2018 (advanced helmets)
- FIA Standard 8865-2015 (racing helmets)
- FIA FT3-1999 (safety fuel tanks)
- ISO/IEC 17025 (competence of testing laboratories)
- LS-DYNA
- Altair HyperWorks
- NI DIAdem
- ANSYS Mechanical
8 modules
1.1History of safety in motorsport1.2Impact biomechanics1.3Human tolerance to deceleration1.4Impact energy and absorption1.5Survival structures1.6Impact attenuators1.7Driver restraint1.8Head protection1.9Organisation of FIA homologation1.10Case study: analysis of a historic accident
2.1Racing seats2.2Safety harnesses2.3Helmets2.4Head restraint devices2.5Flame-resistant clothing2.6Safety fuel tanks2.7Plumbed-in extinguishers2.8Window nets2.9Technical lists of homologated equipment2.10Practical exercise: checking labels and homologations
3.1Roll bars and roll cages3.2Appendix J requirements3.3Materials and joints3.4Finite element calculation3.5Static load testing3.6Side protection3.7Impact structures in single-seaters3.8Fixings and anchorages3.9Homologation documentation3.10Laboratory: static load test of a roll hoop
4.1Impact sleds and catapults4.2Frontal crash tests4.3Side impact tests4.4Anthropomorphic test dummies4.5Accelerometers and high-speed cameras4.6Injury criteria4.7Seat testing4.8Harness testing4.9Laboratory safety4.10Workshop: preparing an impact sled test
5.1Explicit finite elements5.2Material and failure models5.3Carbon composite models5.4Dummy models5.5Validation against tests5.6Structural optimisation5.7Simulation of attenuators5.8Sensitivity analysis5.9Simulation report5.10Practical exercise: simulation of an impact attenuator
6.1Flammability testing of materials6.2Thermal resistance of clothing6.3Extinguisher testing6.4Fuel tanks and leaks6.5Circuit breakers and electrical systems6.6High-voltage batteries6.7Rollover testing6.8Testing of active safety components6.9Systems compatibility6.10Laboratory: flammability test of a material
7.1Accreditation of testing laboratories7.2Metrological traceability7.3Measurement uncertainty7.4Test procedures7.5Sample management7.6Test reports7.7Audits7.8Relationship with the FIA and national federations7.9Confidentiality with manufacturers7.10Case study: audit of a test procedure
8.1Selection of the component8.2Homologation requirements8.3Simulation plan8.4Test plan8.5Analysis of results8.6Proposed improvements8.7Homologation file8.8Final report8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
The programme is delivered 100% online on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so it can be combined with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is LS-DYNA, Altair HyperWorks, NI DIAdem and ANSYS Mechanical, in free, academic or evaluation versions. Testing is studied through real procedures: static load testing of safety structures, dynamic impact sled testing and finite element simulation of attenuators. Assessment is continuous by module plus the final integrating project.
Standards covered: FIA Appendix J, Article 253, FIA Standard 8862-2009, FIA Standard 8853-2016, FIA Standard 8860-2018, FIA Standard 8865-2015, FIA FT3-1999, ISO/IEC 17025.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with LS-DYNA, Altair HyperWorks, NI DIAdem and ANSYS Mechanical, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the programme software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Postgraduate Diploma in Short-Run Machining and Special-Purpose Tooling
Online 800-hour Postgraduate Diploma in Short-Run Machining and Special-Purpose Tooling. 8 modules with ISO 2768-1 (general tolerances), ISO 286-1 (ISO system of limits and fits) and…
Diploma in Roadbooks, Navigation and Timing
Online postgraduate diploma of 800 hours in roadbooks, navigation and timing for classic regularity rallies, structured in 8 modules covering regularity fundamentals, roadbook interpretation, cartography, instrumentation…
Postgraduate Diploma in Auxiliary Electrical Systems: Winches, Lighting and 12V
Online 800-hour Postgraduate Diploma in Auxiliary Electrical Systems: Winches, Lighting and 12V. 8 modules covering ISO 6722-1 (electrical cables for vehicles), ISO 8820 (fuses for road…
More in Restoration & Classics
All Restoration & Classics programmes → · How to apply · Fees & financing · Scholarships