Diploma in Brake Validation on Low-Grip Surfaces
Online postgraduate diploma of 800 hours in brake validation on low-grip surfaces: 8 modules covering tyre-road grip, anti-lock braking systems, stability control, test procedures, instrumentation and data, simulation and virtual validation, and winter test campaigns, with an assigned technical tutor.
Diploma in Brake Validation on Low-Grip Surfaces — studying from Malta
Malta's rich heritage, including historic buildings, vintage vehicles and maritime craft, creates a niche for restoration and conservation work. Owners of classic cars, motorcycles and boats seek specialist workshops with knowledge of period engineering and materials. Restoration of historic architecture also requires engineers and technicians familiar with traditional construction methods and conservation rules. Opportunities tend to be found with specialist workshops, heritage organisations and private restorers.
Fees for Malta: €1,090 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a recognised professional body in Malta for restoration and classic vehicle engineering?
Malta does not have a single state-regulated profession for classic vehicle restoration. Vehicle registration and roadworthiness are handled by Transport Malta. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is determined by employers, clients or the relevant body, so check these before enrolling.
What work could restoration engineers find in Malta?
Malta has a niche market for classic vehicle restoration, mainly through independent workshops, specialist garages and private collectors. Work is often built on reputation and practical craftsmanship. Whether a private online qualification adds value is for individual clients and employers to judge, so it is best to consider it alongside your hands-on experience.
Can I study this part-time with a workshop job, and is funding possible?
Yes. The programmes are fully online, taught in English and suitable for study from home, without needing a student visa. Hours range from 300 to 1,900 depending on the programme. Fees are payable in instalments, employer sponsorship is possible, and each student has an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand tyre-road grip on slippery surfaces.
Analyse how anti-lock braking systems work.
Assess stability control systems.
Apply standardised braking test procedures.
Instrument vehicles and analyse test data.
Validate systems through simulation and hardware-in-the-loop.
Plan winter test campaigns.
Who it's for
- Brake validation engineers.
- Chassis control systems engineers.
- Test drivers.
- ABS calibration engineers.
- Instrumentation technicians.
- Vehicle simulation engineers.
- Engineering or science graduates seeking to join vehicle manufacturers.
What you'll work with
- UNECE Regulation No. 13-H (braking of passenger cars)
- UNECE Regulation No. 13 (braking of heavy vehicles and trailers)
- UNECE Regulation No. 140 (electronic stability control)
- ISO 21994 (stopping distance at straight-line braking with ABS)
- ISO 7975 (braking in a turn, open-loop test)
- ISO 14512 (straight-ahead braking on split-mu surfaces)
- ASTM E1337 (peak braking coefficient using a standard reference test tyre)
- ASTM F2493 (standard reference test tyre)
- MATLAB/Simulink
- CarSim
- IPG CarMaker
- Racelogic VBOX Test Suite
8 modules
1.1Coefficient of friction1.2Longitudinal slip1.3The mu-slip curve1.4Ice, snow, water and gravel1.5Effect of temperature1.6Winter and studded tyres1.7Split-mu surfaces1.8Measuring the coefficient of friction1.9Reference tyre1.10Practical: measuring the coefficient on different surfaces
2.1Operating principle2.2Wheel speed sensors2.3Hydraulic modulators2.4Control cycles2.5Vehicle speed estimation2.6Split-mu strategies2.7ABS on motorcycles2.8ABS on heavy vehicles2.9ABS with regenerative braking2.10Laboratory: analysing control cycles on a test rig
3.1Lateral dynamics on low grip3.2Yaw rate and acceleration sensors3.3Brake intervention3.4Engine intervention3.5Traction control3.6Regulatory requirements3.7Calibration by surface3.8Interaction with the driver3.9Driving modes3.10Practical: stability manoeuvre in a simulator
4.1Straight-line braking4.2Braking in a turn4.3Split-mu braking4.4Braking across a surface transition4.5Stopping distance4.6Repeatability and track preparation4.7Weather conditions4.8Vehicle instrumentation4.9Acceptance criteria4.10Workshop: winter test plan
5.1High-frequency GPS systems5.2Inertial platforms5.3Brake pressure sensors5.4Wheel torque measurement5.5Driving robots5.6Data acquisition5.7Signal synchronisation5.8Processing and filtering5.9Test reports5.10Laboratory: analysing an ABS stop
6.1Vehicle models6.2Tyre models on low grip6.3Hardware-in-the-loop6.4Surface simulation6.5Correlation with track data6.6Virtual test scenarios6.7Software validation6.8Reducing physical testing6.9Limitations of simulation6.10Practical: simulating split-mu braking
7.1Frozen-lake test centres7.2Campaign planning7.3Logistics in extreme climates7.4Personnel safety7.5Track preparation7.6Prototype management7.7Confidentiality7.8Campaign costs7.9Final report7.10Case study: plan for a two-week winter campaign
8.1Defining the system8.2Test requirements8.3Simulation plan8.4Track test plan8.5Instrumentation8.6Analysis of results8.7Calibration proposal8.8Technical report8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
A 100% online programme on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so you can combine it with your job.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is MATLAB/Simulink, CarSim, IPG CarMaker and Racelogic VBOX Test Suite, in free, academic or evaluation versions. Testing is studied through real procedures: split-mu braking on ice, stopping distance measurement on snow and hardware-in-the-loop simulation of an ABS. Assessment is continuous by module, plus the final project.
Standards covered: UNECE Regulation No. 13-H, UNECE Regulation No. 13, UNECE Regulation No. 140, ISO 21994, ISO 7975, ISO 14512, ASTM E1337, ASTM F2493.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with MATLAB/Simulink, CarSim, IPG CarMaker and Racelogic VBOX Test Suite, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in Vintage Two-Stroke and Four-Stroke Engines: Rebuilding and Tuning
Online postgraduate diploma of 800 hours in rebuilding and tuning vintage two-stroke and four-stroke engines: 8 modules covering period engine types, dismantling and metrology, cylinders and…
Diploma in Cooling, Brakes and Thermal Management
Online postgraduate diploma of 800 hours in cooling, brakes and thermal management, with 8 modules covering vehicle heat transfer, engine cooling, oil and transmission cooling, brake…
Diploma in Conservation and Maintenance of Structures
Online postgraduate diploma of 800 hours in the conservation and maintenance of vehicle structures. 8 modules covering historic structural materials, deterioration mechanisms, condition assessment, conservation treatments,…
More in Restoration & Classics
All Restoration & Classics programmes → · How to apply · Fees & financing · Scholarships