Course in Destructive and Non-Destructive Testing of Materials
300-hour online course in destructive and non-destructive testing of materials. 6 modules covering ISO 6892-1 (tensile testing at room temperature), ISO 148-1 (Charpy impact test) and CIVA. Assigned tutor and open enrolment.
Course in Destructive and Non-Destructive Testing of Materials — studying from Malta
Malta has no nuclear power generation, and its nuclear engineering relevance lies mainly in radiation protection, safeguards awareness, medical and industrial radiation use, and regulatory oversight of radioactive materials. The Malta Radiation Protection Department and the Health Directorate oversee the use of radiation in hospitals, research and industry. Engineers may find roles in medical physics support, radiological monitoring and compliance. The sector is largely confined to applied and regulatory work rather than fuel cycle activity.
Fees for Malta: €743 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a professional route in Malta for nuclear engineering, and is SEIUM's qualification recognised?
Malta does not operate nuclear power plants, so nuclear engineering careers there are limited, and roles are more likely in regulation, consultancy or international work. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is decided by employers or the relevant regulatory body, so verify this before enrolling.
What employment could this training lead to in Malta?
Given Malta has no nuclear power generation, local opportunities are few and would mostly sit within consultancy, international organisations or firms working abroad. Employers in these roles set their own qualification requirements, and a private online qualification may or may not be accepted. Reviewing job requirements and speaking with employers will show how the training would be viewed.
Can I study this from Malta without relocating, and how is the workload structured?
Yes, the programmes are 100% online, taught in English and suitable for study from home, so you do not need a student visa. Master's programmes total 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. Each student has an assigned technical tutor, and fees are payable in instalments, with possible employer sponsorship.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the fundamentals of materials characterisation.
Carry out and interpret destructive mechanical tests.
Apply metallography and failure analysis techniques.
Select the appropriate non-destructive testing method.
Interpret NDT indications against acceptance criteria.
Describe the qualification of procedures and personnel.
Develop an inspection plan for a nuclear component.
Who it's for
- Materials testing engineer who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Level 2 NDT inspector who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Failure analysis specialist who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- In-service inspection engineer who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Metallographic laboratory technician who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Welding quality engineer who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Engineering or science graduates seeking to enter nuclear power plants.
What you'll work with
- ISO 6892-1 (tensile testing at room temperature)
- ISO 148-1 (Charpy impact test)
- ISO 9712 (qualification of NDT personnel)
- ASME BPVC Section V (non-destructive examination)
- ASME BPVC Section XI (in-service inspection)
- ASTM E399 (fracture toughness KIc)
- ISO 17640 (ultrasonic testing of welded joints)
6 modules · 300 h
1.1What needs to be known about a material and which test reveals it1.2Destructive vs non-destructive testing: when each applies1.3Specimen, sampling and representativeness1.4Traceability, calibration and reference standards1.5Measurement uncertainty in mechanical testing1.6Test standards and laboratory accreditation1.7The test report: what it must contain to be valid1.8Acceptance criteria and material specification1.9Laboratory safety1.10Exercise: choosing the test battery for a specification
2.1Tensile: curve, yield strength, tensile strength and elongation2.2Brinell, Vickers and Rockwell hardness: which to use and why2.3Toughness and Charpy impact; transition temperature2.4Fatigue: S-N curves and governing factors2.5Creep and creep rupture at high temperature2.6Fracture mechanics and toughness measurement2.7Bend, flattening and drawing tests2.8Tests on welded joints2.9Effect of irradiation on mechanical properties2.10Practice: interpreting a set of tensile and impact results
3.1Sample preparation: cutting, mounting, polishing and etching3.2Optical and electron microscopy3.3Identification of phases and microstructure3.4Grain size, inclusions and defects3.5Chemical and compositional analysis3.6Fractography: learning to read the fracture surface3.7Failure mechanisms: fatigue, stress corrosion cracking and embrittlement3.8Ordered sequence of a failure investigation3.9Failure analysis report with defensible conclusions3.10Practice: analysing a real in-service fracture case
4.1Visual inspection and its scope, always underestimated4.2Liquid penetrant testing: procedure and limitations4.3Magnetic particle testing and ferromagnetic materials4.4Eddy currents and thickness measurement4.5Contact ultrasonics: probes and calibration4.6Advanced techniques: phased array and TOFD4.7Industrial radiography and digital radiography4.8Thermography and acoustic emission4.9Choosing the technique according to the defect sought4.10Practice: detecting and sizing defects in a specimen
5.1Qualification and certification of testing personnel5.2Written procedures and their approval5.3Qualification of inspection procedures5.4Inspection plans for manufacturing and in service5.5Inspection of pressure vessels and pipework5.6Remote inspection and inspection in radiation environments5.7Evaluation of indications and acceptance criteria5.8Fitness-for-service assessment5.9Recording, traceability and archiving of inspections5.10Practice: drafting an inspection procedure
6.1Choice of component and its service context6.2Material specification and applicable requirements6.3Destructive and non-destructive test plan6.4Execution and recording of tests6.5Joint interpretation of all results6.6Fitness-for-service assessment and remaining life estimation6.7Periodic inspection recommendations6.8Cost of the test plan6.9Technical report6.10Defence of the work
How you'll learn
100 % online training on the SEIUM campus, with downloadable material, recorded classes and a dedicated technical tutor. There are no fixed timetables: students progress at their own pace within the intake, which makes it possible to combine the programme with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is CIVA, Instron Bluehill, ImageJ/Fiji, UltraVision (Zetec), in free, academic or evaluation versions. Tests are studied using real procedures for tensile, hardness and Charpy testing, metallography and fractography, and ultrasonic and eddy current inspection. Assessment is continuous, module by module, plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the fundamentals of materials characterisation.
Carry out and interpret destructive mechanical tests.
Apply metallography and failure analysis techniques.
Select the appropriate non-destructive testing method.
Interpret NDT indications against acceptance criteria.
Where this takes you
Requirements
- No previous degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow the reading of technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours, spread over 3 to 5 months. That is between 10 and 15 hours per week on average, compatible with full-time work.
You work with CIVA, Instron Bluehill, ImageJ/Fiji, UltraVision (Zetec). Free, academic or evaluation versions are used, and the tutor indicates the open-source alternative where one exists.
SEIUM's own diploma upon passing the continuous assessment and the integrative project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised in the advanced programme. Check the recognition policy when enrolling.
Related programmes
Course in Corrosion under Irradiation in Reactors
Online 300-hour course in corrosion under irradiation in reactors. 6 modules covering ASME BPVC Section XI (in-service inspection), NUREG-1801 (GALL report on ageing management) and Thermo-Calc.…
Course in Chemical and Physical Decontamination Strategies
Online 300-hour course in chemical and physical decontamination strategies. 6 modules covering ISO 7503 (surface contamination measurement), IAEA GSR Part 6 (decommissioning of facilities) and VISIPLAN.…
Course on Autonomous Robots for Nuclear Inspection
Online course of 300 h in Autonomous Robots for Nuclear Inspection. 6 modules covering UL 4600 (safety of autonomous products), IEEE 7001 (transparency of autonomous systems)…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships