Classic Heavy-Vehicle Transmissions Course
Online 300-hour course in classic heavy-vehicle transmissions. 6 modules covering ISO 6336 (gear load capacity calculation), ISO 10825-1 (wear and damage on gear teeth) and KISSsoft. Tutor assigned and enrolment open.
Classic Heavy-Vehicle Transmissions Course — studying from Malta
Malta's rich heritage, including historic buildings, vintage vehicles and maritime craft, creates a niche for restoration and conservation work. Owners of classic cars, motorcycles and boats seek specialist workshops with knowledge of period engineering and materials. Restoration of historic architecture also requires engineers and technicians familiar with traditional construction methods and conservation rules. Opportunities tend to be found with specialist workshops, heritage organisations and private restorers.
Fees for Malta: €797 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Malta
Typical roles
Questions from Malta
Is there a recognised professional body in Malta for restoration and classic vehicle engineering?
Malta does not have a single state-regulated profession for classic vehicle restoration. Vehicle registration and roadworthiness are handled by Transport Malta. SEIUM Institute's qualifications are private, not official state degrees, and are not accredited by any national body. Recognition is determined by employers, clients or the relevant body, so check these before enrolling.
What work could restoration engineers find in Malta?
Malta has a niche market for classic vehicle restoration, mainly through independent workshops, specialist garages and private collectors. Work is often built on reputation and practical craftsmanship. Whether a private online qualification adds value is for individual clients and employers to judge, so it is best to consider it alongside your hands-on experience.
Can I study this part-time with a workshop job, and is funding possible?
Yes. The programmes are fully online, taught in English and suitable for study from home, without needing a student visa. Hours range from 300 to 1,900 depending on the programme. Fees are payable in instalments, employer sponsorship is possible, and each student has an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Describe the transmissions of classic heavy vehicles and their evolution.
Rebuild clutches and their mechanical and hydraulic actuation.
Strip down and rebuild non-synchronised and synchronised gearboxes.
Adjust clearances, preloads and contact patterns in differentials and axles.
Diagnose faults from noises, vibrations and oil analysis.
Select lubricants compatible with yellow metals and legacy seals.
Locate or reproduce spare parts for discontinued transmissions.
Who it's for
- Classic heavy-vehicle transmission technician wishing to specialise in Classic Heavy-Vehicle Transmissions.
- Gearbox rebuilder wishing to specialise in Classic Heavy-Vehicle Transmissions.
- Historic truck mechanic wishing to specialise in Classic Heavy-Vehicle Transmissions.
- Differential and axle specialist wishing to specialise in Classic Heavy-Vehicle Transmissions.
- Transmission diagnostics technician wishing to specialise in Classic Heavy-Vehicle Transmissions.
- Workshop manager for historic commercial vehicles wishing to specialise in Classic Heavy-Vehicle Transmissions.
- Graduates in engineering or science seeking to enter commercial vehicle restoration.
What you'll work with
- ISO 6336 (gear load capacity calculation)
- ISO 10825-1 (wear and damage on gear teeth)
- SAE J306 (gear lubricant viscosity grades)
- ISO 1328-1 (accuracy of cylindrical gears)
- ISO 281 (rolling bearing life)
- ISO 15243 (rolling bearing damage and failure)
- Royal Decree 892/2013 (Historic Vehicles Regulation)
6 modules · 300 h
1.1Drivetrain architecture1.2Spur-gear gearboxes1.3Synchromesh gearboxes1.4Multiplier and reduction groups1.5Two-range gearboxes1.6Double-reduction rear axles1.7Power take-offs1.8Nomenclature and ratios1.9Documentation and workshop manuals1.10Workshop: identifying a transmission
2.1Single- and twin-plate dry clutches2.2Wear and diagnosis2.3Mechanical, hydraulic and pneumatic actuation2.4Servo clutch and its repair2.5Travel and clearance adjustment2.6Flywheel and its machining2.7Thrust bearing2.8Clutch replacement on heavy vehicles2.9Safety when handling heavy assemblies2.10Practice: replacing and adjusting a clutch
3.1Removing the gearbox from the vehicle3.2Orderly disassembly and marking3.3Inspection of gears and shafts3.4Bearings and their replacement3.5Synchronisers and their wear3.6Selector forks, linkage and locking3.7Clearances, preloads and shims3.8Seals and sealing3.9Assembly and bench testing3.10Practice: rebuilding a gearbox
4.1Propeller shafts and universal joints4.2Working angles and vibrations4.3Shaft balancing4.4Rear axle: disassembly4.5Bevel gear set and its adjustment4.6Contact pattern and its interpretation4.7Differential and locking4.8Hub reduction units4.9Lubrication and breathers4.10Practice: adjusting a bevel gear set
5.1Noises and their location5.2Gear engagement difficulty and its causes5.3Gear jumping out5.4Leaks and their origin5.5Transmission overheating5.6Vibrations and their diagnosis5.7Oil and particle analysis5.8Usage history as a clue5.9Decision to repair or replace5.10Practice: guided diagnosis of three faults
6.1Suitable transmission oils6.2Compatibility with bronzes and seals6.3Oil change intervals6.4Discontinued spare parts and alternatives6.5Manufacturing parts and shims6.6Grinding and recovery of parts6.7Recording the work carried out6.8Common workshop errors6.9Documented real cases6.10Final project: documented rebuild of a transmission
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetable: students progress at their own pace within the intake, which makes it possible to combine with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is KISSsoft, Fusion 360, advanced Excel, SKF Bearing Select, in free, academic or evaluation versions. Tests are studied using real procedures on gearbox strip-down benches, transmission oil analysis, clearance checks and differential preload verification. Assessment is continuous per module plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Describe the transmissions of classic heavy vehicles and their evolution.
Rebuild clutches and their mechanical and hydraulic actuation.
Strip down and rebuild non-synchronised and synchronised gearboxes.
Adjust clearances, preloads and contact patterns in differentials and axles.
Diagnose faults from noises, vibrations and oil analysis.
Where this takes you
Requirements
- No prior degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours, spread over 3 to 5 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
The work is carried out with KISSsoft, Fusion 360, advanced Excel and SKF Bearing Select. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM Institute diploma upon passing the continuous assessment and the integrative project. This is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised towards the higher programme. Check the recognition policy when you enrol.
Related programmes
Course in Restoration of Veneered Wood Interiors
Online 300-hour course in restoration of veneered wood interiors. 6 modules covering UNE-EN 13556 (wood nomenclature), EN 204 (classification of wood adhesives) and SketchUp (panel layout).…
Course in Classic and Collectible Vehicle Valuation
Online 300-hour course in classic and collectible vehicle valuation. 6 modules covering International Valuation Standards (IVS), UNE 197001:2019 (expert reports and opinions) and advanced Excel. Assigned…
Case Study Course: Mille Miglia
Online 300-hour course in Case Studies: Mille Miglia. 6 modules covering the FIVA Event Code, the FIVA Technical Code and Tripy (regularity navigation). Assigned tutor and…
More in Restoration & Classics
All Restoration & Classics programmes → · How to apply · Fees & financing · Scholarships