Course on Safety in Liquid Waste Handling
Online 300-hour course on safety in liquid waste handling. 6 modules covering IAEA GSR Part 5 (predisposal management of radioactive waste), IAEA SSG-40 (radioactive waste management for nuclear power plants) and PHREEQC. Personal tutor assigned and open enrolment.
Course on Safety in Liquid Waste Handling — studying from India
India's nuclear programme is state-led and centred on the Department of Atomic Energy, with operations managed by the Nuclear Power Corporation of India and research carried out at the Bhabha Atomic Research Centre. Reactor sites are located at places such as Tarapur, Kakrapar, Kudankulam and Rawatbhata. Regulation is handled by the Atomic Energy Regulatory Board, which sets safety standards for reactors and fuel facilities. Engineers in this field work on reactor systems, fuel cycle technologies, radiation safety and materials, with expertise supported by institutions such as the Indira Gandhi Centre for Atomic Research.
Fees for India: ₹57,900 (Indian Rupee), with instalments and employer sponsorship available.
Relevant bodies in India
Typical roles
Questions from India
Who regulates nuclear engineering work in India and does this course satisfy them?
The Atomic Energy Regulatory Board (AERB) regulates nuclear safety in India, and the Department of Atomic Energy runs the sector. SEIUM's qualification is private, not an official degree, and is not accredited by any national body. It does not satisfy any regulatory requirement, and AERB or the employer will decide what qualifications they require.
Which Indian employers work in nuclear engineering and the fuel cycle?
Public sector nuclear organisations and their associated industries are the main employers, and entry normally follows government recruitment and vetting processes. Private employers in the sector also exist. Because hiring is tightly controlled, a private online qualification is unlikely to be the deciding factor, and recognition depends on the employer.
Is this programme workable with a job in India, and how is it funded?
The programme is online and taught in English, so you can study from home across India without a student visa. Each student is assigned a technical tutor and completes a final project. Fees are payable in instalments, and employer sponsorship is possible, which is often the practical route for working engineers.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Classify liquid radioactive waste according to its origin and activity.
Describe treatment processes such as evaporation and ion exchange.
Apply containment measures and leak prevention.
Assess the radiological and chemical risks of handling.
Apply the ALARA principle to liquid operations.
Control discharges within authorised limits.
Develop a safe procedure for handling liquid waste.
Who it's for
- Radioactive waste management technician who wants to specialise in Safety in Liquid Waste Handling.
- Effluent treatment engineer who wants to specialise in Safety in Liquid Waste Handling.
- Radiation protection technician who wants to specialise in Safety in Liquid Waste Handling.
- Nuclear chemical engineer who wants to specialise in Safety in Liquid Waste Handling.
- Facility safety manager who wants to specialise in Safety in Liquid Waste Handling.
- Radiochemistry laboratory technician who wants to specialise in Safety in Liquid Waste Handling.
- Engineering or science graduates seeking to enter radioactive waste management.
What you'll work with
- IAEA GSR Part 5 (predisposal management of radioactive waste)
- IAEA SSG-40 (radioactive waste management for nuclear power plants)
- Directive 2011/70/Euratom (management of spent fuel and radioactive waste)
- Royal Decree 102/2014 (responsible management of radioactive waste)
- IAEA GSR Part 3 (radiation protection)
- ISO 10648-2 (containment enclosures: leaktightness)
6 modules · 300 h
1.1Origin: power plants, hospitals, laboratories and industry1.2Classification by activity and by period1.3Chemical composition and its influence on treatment1.4Aqueous waste, organic waste and mixtures1.5Scintillation liquids and solvents1.6Compatibility and flammability issues1.7Regulatory framework for waste management1.8Exemption criteria and authorised discharge1.9Responsibilities of the producer1.10Exercise: classify a real inventory
2.1Segregation at source and labelling2.2Suitable containers and their compatibility2.3Double containment and retention bunds2.4Temporary storage areas and their design2.5Ventilation and leak detection2.6Inventory control and traceability2.7Controlled decay of short-lived isotopes2.8Concurrent non-radiological hazards2.9Chemical incompatibilities to avoid2.10Practice: design a temporary store
3.1Written decanting procedures3.2Tools and shielding for liquids3.3Prevention of aerosols and splashes3.4Appropriate personal protective equipment3.5Fume hoods, cabinets and enclosures3.6Pump and gravity transfer3.7Contamination checks after the operation3.8Responding to a spill: containment and absorption3.9Decontamination of surfaces and equipment3.10Practice: active liquid spill drill
4.1Evaporation and concentration4.2Ion exchange and resins4.3Filtration and ultrafiltration4.4Chemical precipitation and flocculation4.5Organic treatment: incineration and oxidation4.6Immobilisation in cement and polymers4.7Quality control of the conditioned product4.8Characterisation of the final waste4.9Generation of secondary waste4.10Practice: select the treatment route
5.1Limits and conditions for authorised discharge5.2Pre-discharge checks and recording5.3Monitoring of effluent and the receiving environment5.4Calculation of public dose from discharge5.5Preparing waste for collection5.6Transfer documentation for the waste contractor5.7Transport of radioactive liquids5.8Document archiving and deadlines5.9Audit of the waste management system5.10Practice: complete file for a waste collection
6.1Choosing the producing facility6.2Inventory and characterisation of the liquids6.3Design of segregation and storage6.4Handling procedures6.5Selection of the treatment route6.6Effluent monitoring plan6.7Emergency plan for spills6.8Staff training plan6.9Report on the waste management plan6.10Project defence
How you'll learn
100 % online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetables: students progress at their own pace within the enrolment period, which makes it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is PHREEQC, MicroShield, advanced Excel, Aspen Plus, in free, academic or evaluation versions. Case studies are based on real effluent treatment procedures using ion exchange, risk analysis of liquid handling, and control of radioactive discharges. Assessment is continuous by module plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Classify liquid radioactive waste according to its origin and activity.
Describe treatment processes such as evaporation and ion exchange.
Apply containment measures and leak prevention.
Assess the radiological and chemical risks of handling.
Apply the ALARA principle to liquid operations.
Where this takes you
Requirements
- No prior degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient command of Spanish to follow technical regulatory reading.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours spread over 3 to 5 months. That is between 10 and 15 hours per week on average, compatible with a full-time job.
The course uses PHREEQC, MicroShield, advanced Excel and Aspen Plus. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM own diploma upon passing the continuous assessment and the integrative project. It is in-house training, not an official Ministry qualification.
Yes. Modules passed in a course or postgraduate diploma in the same area are credited towards the higher programme. Check the recognition policy when you enrol.
Related programmes
Course in Corrosion under Irradiation in Reactors
Online 300-hour course in corrosion under irradiation in reactors. 6 modules covering ASME BPVC Section XI (in-service inspection), NUREG-1801 (GALL report on ageing management) and Thermo-Calc.…
Experimental Validation of Nuclear Models Course
Online 300-hour course in experimental validation of nuclear models. 6 modules with JCGM 100:2008 (GUM, Guide to the Expression of Uncertainty in Measurement), JCGM 101:2008 (propagation…
Course in Superconducting Technologies in Fusion
Online 300-hour course in superconducting technologies in fusion. 6 modules covering IEC 61788-1 (critical current in Nb-Ti conductors), IEC 61788-2 (critical current in Nb3Sn conductors) and…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships