Course on Hybrid Fission-Fusion Power Generation
Online course of 300 h in Hybrid Fission-Fusion Power Generation. 6 modules covering ASME BPVC Section III, Division 4 (fusion energy device components), IAEA SSR-2/1 (Rev. 1) (safety of nuclear power plants: design) and MCNP. Dedicated tutor and enrolment open.
Course on Hybrid Fission-Fusion Power Generation — studying from India
India's nuclear programme is state-led and centred on the Department of Atomic Energy, with operations managed by the Nuclear Power Corporation of India and research carried out at the Bhabha Atomic Research Centre. Reactor sites are located at places such as Tarapur, Kakrapar, Kudankulam and Rawatbhata. Regulation is handled by the Atomic Energy Regulatory Board, which sets safety standards for reactors and fuel facilities. Engineers in this field work on reactor systems, fuel cycle technologies, radiation safety and materials, with expertise supported by institutions such as the Indira Gandhi Centre for Atomic Research.
Fees for India: ₹57,900 (Indian Rupee), with instalments and employer sponsorship available.
Relevant bodies in India
Typical roles
Questions from India
Who regulates nuclear engineering work in India and does this course satisfy them?
The Atomic Energy Regulatory Board (AERB) regulates nuclear safety in India, and the Department of Atomic Energy runs the sector. SEIUM's qualification is private, not an official degree, and is not accredited by any national body. It does not satisfy any regulatory requirement, and AERB or the employer will decide what qualifications they require.
Which Indian employers work in nuclear engineering and the fuel cycle?
Public sector nuclear organisations and their associated industries are the main employers, and entry normally follows government recruitment and vetting processes. Private employers in the sector also exist. Because hiring is tightly controlled, a private online qualification is unlikely to be the deciding factor, and recognition depends on the employer.
Is this programme workable with a job in India, and how is it funded?
The programme is online and taught in English, so you can study from home across India without a student visa. Each student is assigned a technical tutor and completes a final project. Fees are payable in instalments, and employer sponsorship is possible, which is often the practical route for working engineers.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the concept of a fission-fusion hybrid system and its applications.
Calculate the neutronic parameters of a subcritical blanket.
Analyse the fusion source requirements for a hybrid system.
Evaluate thermal-hydraulic behaviour and energy conversion.
Identify the specific safety, waste and safeguards aspects.
Apply neutron transport and activation tools.
Develop a conceptual design of a hybrid system.
Who it's for
- Neutronics engineer looking to specialise in Hybrid Fission-Fusion Power Generation.
- Advanced reactor design engineer looking to specialise in Hybrid Fission-Fusion Power Generation.
- Nuclear fusion researcher looking to specialise in Hybrid Fission-Fusion Power Generation.
- Thermal-hydraulics engineer looking to specialise in Hybrid Fission-Fusion Power Generation.
- Nuclear safety analyst looking to specialise in Hybrid Fission-Fusion Power Generation.
- Licensing specialist looking to specialise in Hybrid Fission-Fusion Power Generation.
- Engineering or science graduates looking to move into fusion research.
What you'll work with
- ASME BPVC Section III, Division 4 (fusion energy device components)
- IAEA SSR-2/1 (Rev. 1) (safety of nuclear power plants: design)
- ANSI/ANS-8.1 (nuclear criticality safety outside reactors)
- IAEA GSR Part 4 (Rev. 1) (safety assessment)
- Directive 2014/87/Euratom (nuclear safety)
- IAEA GSR Part 5 (predisposal management of radioactive waste)
- INFCIRC/153 (safeguards)
6 modules · 300 h
1.1History of the concept: the proposals of Bethe and Sakharov1.2Fusion neutron source and subcritical blanket1.3Energy multiplication in the blanket1.4Fusion Q factor required in a hybrid1.5Comparison with ADS systems1.6Applications: energy, transmutation and fuel breeding1.7Current debate and programmes in China and Russia1.8Advantages and limitations versus pure fission1.9Non-proliferation aspects of the hybrid1.10Case study: energy balance of a conceptual hybrid
2.1Subcritical multiplication factor ks2.2The 14 MeV spectrum and threshold reactions2.3Multiplication by (n,2n) and fast fission2.4External source and gain calculation2.5Fuels: uranium, thorium and minor actinides2.6Tritium breeding in the blanket2.7Burn-up and isotopic evolution2.8Transport codes for hybrid blankets2.9Validation with blanket experiments2.10Lab: multiplication calculation with a simplified model
3.1Compact tokamak as a neutron source3.2Magnetic mirrors and linear configurations3.3Inertial confinement fusion sources3.4Neutron wall loading3.5Availability and load factor3.6FDS designs from China's ASIPP3.7Livermore's LIFE concept3.8Georgia Tech's SABR design3.9Source-blanket geometric interaction3.10Practice: sizing a neutron source for a blanket
4.1Coolants: helium, sodium, lead-lithium and salts4.2Heat extraction from the blanket4.3Power distribution and density peaks4.4Brayton and Rankine power cycles4.5Balance of plant and recirculating power4.6Net system efficiency4.7Decay heat management4.8Compatible structural materials4.9Magnetohydrodynamic coupling4.10Case study: balance of plant of a 1000 MWt hybrid
5.1Inherent safety of the subcritical system5.2Loss-of-source transients5.3Radioactive inventory compared with a fission reactor5.4Transmutation of minor actinides5.5Tritium inventory and confinement5.6Safeguards applied to the hybrid5.7Fission and fusion regulatory frameworks5.8Economics and feasibility of the concept5.9Critical assessment and alternatives5.10Workshop: comparative safety analysis
6.1Defining the hybrid's mission6.2Selecting the fusion source6.3Blanket and fuel design6.4Neutronic multiplication calculation6.5Energy and thermal-hydraulic balance6.6Safety and waste analysis6.7Feasibility assessment6.8Design summary6.9Report and presentation6.10Final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable materials, recorded classes and a dedicated technical tutor. No fixed timetable: students progress at their own pace within the intake period, making it easy to combine with work.
Each module combines theory, guided reading of the original standards and applied exercises. The software used is MCNP, Serpent, OpenMC, FISPACT-II, COMSOL Multiphysics, in free, academic or trial versions. Testing is studied through real procedures from neutronic calculation of a subcritical blanket, energy balance of a hybrid system, actinide transmutation analysis. Assessment is continuous for each module, plus a final capstone project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the concept of a fission-fusion hybrid system and its applications.
Calculate the neutronic parameters of a subcritical blanket.
Analyse the fusion source requirements for a hybrid system.
Evaluate thermal-hydraulic behaviour and energy conversion.
Identify the specific safety, waste and safeguards aspects.
Where this takes you
Requirements
- No previous qualification is required.
- An internet connection and a computer able to run the programme software.
- A level of English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours spread over 3 to 5 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
You will work with MCNP, Serpent, OpenMC, FISPACT-II, COMSOL Multiphysics. Free, academic or trial versions are used, and your tutor will point out a free alternative where one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the capstone project. It is SEIUM's own qualification, not an official state-accredited degree.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised in the higher programme. Check the recognition policy when you enrol.
Related programmes
Course in Atmospheric Radiological Dispersion Simulation
Online 300 h course in atmospheric radiological dispersion simulation. 6 modules aligned with IAEA GSR Part 7 (emergency preparedness and response), IAEA GSG-2 (criteria for nuclear…
Course on International Environmental Regulation in Nuclear
Online course of 300 h in International Environmental Regulation in Nuclear. 6 modules covering Directive 2011/92/EU (environmental impact assessment), as amended by 2014/52/EU, Euratom Treaty, Articles…
Course on Digital Control in Tokamaks
Online course of 300 h in Digital Control in Tokamaks. 6 modules covering IEC 61131-3 (PLC programming languages), IEC 61508 (functional safety) and MATLAB/Simulink. Dedicated tutor…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships