Postgraduate Diploma in Heat Exchangers, Shrouds and Thermal Packaging
Online 800-hour Postgraduate Diploma in Heat Exchangers, Shrouds and Thermal Packaging. 8 modules with TEMA Standards, ASME PTC 30 and GT-SUITE. Assigned tutor and open enrolment.
Postgraduate Diploma in Heat Exchangers, Shrouds and Thermal Packaging — studying from Ireland
Ireland has a modest automotive footprint, with activity centred on component supply, automotive electronics, testing and aftermarket services rather than vehicle assembly. Motorsport and performance engineering are represented by teams, specialist workshops and engineering consultancies, often linked to the Irish motorsport community. Engineers in this area work on powertrain components, vehicle dynamics, sensor integration and testing for both established manufacturers and suppliers. Regulatory oversight for road vehicles comes from national and European type-approval bodies, while industry collaboration is coordinated through automotive and engineering associations.
Fees for Ireland: €1,290 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Ireland
Typical roles
Questions from Ireland
Which Irish bodies are relevant for recognising automotive engineering qualifications?
In Ireland, Engineers Ireland is the principal professional body for engineers and runs chartered engineer registration. Automotive vehicle standards and roadworthiness fall under the Road Safety Authority and the National Car Test system. SEIUM's qualifications are private and not accredited by any national body, so their recognition is for employers or the relevant body to decide. Confirm this with them before enrolling if it matters for your career.
Where do automotive and motorsport engineers typically work in Ireland, and do employers value online study?
Ireland has automotive supply chain and engineering activity, along with motorsport and vehicle-related design roles, though it is a smaller market than larger European countries. Employers usually weigh practical experience and proven skills heavily. An online private qualification can complement a CV, but whether it is valued depends on each employer, and no outcome can be guaranteed.
How do I fit this programme around work and what language level is needed?
Study is fully online and taught in English, so you need a good working command of English for technical reading and written assignments. Master's programmes are 1,900 hours, postgraduate diplomas 800 hours and specialist courses 300 hours. Each student receives an assigned technical tutor. Fees can be paid in instalments, and employer sponsorship may be possible, so raise that with your employer early.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Size heat exchangers using LMTD and e-NTU methods.
Select radiator technologies suited to competition.
Design shrouds that maximise flow uniformity.
Resolve thermal packaging using mass and aerodynamic criteria.
Model cooling circuits under transient conditions.
Simulate the thermal system using CFD.
Validate thermal performance through testing and telemetry.
Who it's for
- Thermal engineer looking to specialise in Heat Exchangers, Shrouds and Thermal Packaging.
- Cooling engineer looking to specialise in Heat Exchangers, Shrouds and Thermal Packaging.
- Packaging engineer looking to specialise in Heat Exchangers, Shrouds and Thermal Packaging.
- CFD engineer looking to specialise in Heat Exchangers, Shrouds and Thermal Packaging.
- Thermal test engineer looking to specialise in Heat Exchangers, Shrouds and Thermal Packaging.
- Motorsport mechanical designer looking to specialise in Heat Exchangers, Shrouds and Thermal Packaging.
- Graduates in engineering or science seeking to enter motorsport.
What you'll work with
- TEMA Standards
- ASME PTC 30
- ISO 5801
- ISO 5167-1
- FIA Formula 1 Technical Regulations
- SAE J1994
- ISO/IEC 17025
8 modules · 800 h
1.1Forced convection in ducts and fins1.2Overall heat transfer coefficient1.3LMTD and effectiveness-NTU methods1.4Colburn and Nusselt correlations1.5Pressure drop on air side and fluid side1.6Fouling factor and degradation1.7Properties of refrigerants and oils1.8Cross-flow heat exchangers1.9Performance at low air speed1.10Practice: sizing using the e-NTU method
2.1Brazed aluminium cores2.2Louvred and corrugated fins2.3Multichannel flat tubes2.4Plate and bar heat exchangers2.5Oil and ERS coolers2.6Air-to-air and air-to-water intercoolers2.7Additive manufacturing of heat exchangers2.8Materials and minimum thicknesses2.9Reliability against stone impact2.10Case study: core comparison for a single-seater
3.1Function of shrouds and internal fairings3.2Radiator inlet diffusers3.3Velocity uniformity across the core3.4Flow separation and recirculation3.5Air outlets and base pressure3.6Radiator inclination and efficiency3.7Joints and sealing against leaks3.8Outlet louvre design3.9Interaction with bodywork flow3.10Workshop: shroud design with CFD
4.1Volume constraints in sidepods4.2Location of radiators and intercoolers4.3Pipe and hose routing4.4Insulation of sensitive components4.5Heat protection and shields4.6Centre of gravity and mass4.7Accessibility for maintenance4.8Integration with structure and crash4.9Trade-offs between aerodynamics and cooling4.10Case study: sidepod packaging
5.11D models of pumps and valves5.2Thermostats and bypass5.3Circuit expansion and pressurisation5.4Pump cavitation5.5Simulation of race transients5.6Safety car and traffic scenarios5.7Coupling with engine model5.8Calibration with track data5.9Flow rate optimisation5.10Lab: cooling circuit in GT-SUITE
6.1Porous media models for cores6.2Dual-stream heat exchanger models6.3Meshing of complete sidepods6.4Representative boundary conditions6.5Post-processing of flow rate and heat rejection6.6Validation with wind tunnel6.7Parametric geometry studies6.8Computational cost and simplifications6.9Correlation with track6.10Practice: simulating a radiator as a porous medium
7.1Radiator tests on air rig7.2Flow rate and temperature measurement7.3Wind tunnel tests with active radiators7.4Thermal telemetry on track7.5Extreme heat tests7.6Leak and pressure analysis7.7Component certification7.8Management of experimental uncertainty7.9Validation report7.10Case study: rig-to-track correlation of an intercooler
8.1Heat rejection requirements8.2Heat exchanger selection8.3Shroud design8.4Sidepod packaging8.51D circuit simulation8.6CFD simulation of the system8.7Test plan8.8Assessment of the aerodynamic trade-off8.9Report and presentation8.10Final review with the tutor
How you'll learn
Training 100% online on the SEIUM campus, with downloadable material, recorded lectures and a dedicated technical tutor. No fixed timetable: students progress at their own pace within the intake, making it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is GT-SUITE, STAR-CCM+, ANSYS Fluent, Simcenter Amesim, CATIA V5, in free, academic or evaluation versions. Testing is studied using real heat exchanger test procedures on air rigs, CFD simulation of sidepods and thermal measurement on track. Assessment is continuous by module, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Size heat exchangers using LMTD and e-NTU methods.
Select radiator technologies suited to competition.
Design shrouds that maximise flow uniformity.
Resolve thermal packaging using mass and aerodynamic criteria.
Model cooling circuits under transient conditions.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow the reading of technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme consists of 800 hours in total, spread over 6 to 8 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
You will work with GT-SUITE, STAR-CCM+, ANSYS Fluent, Simcenter Amesim, CATIA V5. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM own diploma upon passing the continuous assessment and the integrating project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area can be credited towards the higher-level programme. Check the credit transfer policy when you enrol.
Related programmes
Postgraduate Diploma in Set-Up for Sprint and Endurance Touring Cars
Online 800-hour Postgraduate Diploma in Set-Up for Sprint and Endurance Touring Cars. 8 modules covering the FIA International Sporting Code, Appendix J, Article 253: safety equipment…
Postgraduate Diploma in Aerodynamic Optimisation with Adjoint/Surrogates
Online 800-hour Postgraduate Diploma in Aerodynamic Optimisation with Adjoint/Surrogates. 8 modules with FIA Formula 1 Technical Regulations, FIA Formula 1 Sporting Regulations and SU2. Dedicated tutor…
Postgraduate Diploma in Spare Parts, Shift and Crisis Room Management
Online 800-hour postgraduate diploma in Spare Parts, Shift and Crisis Room Management. 8 modules covering ISO 22361:2022 crisis management, ISO 22320 emergency management and SAP S/4HANA.…
More in Automotive & Motorsport
All Automotive & Motorsport programmes → · How to apply · Fees & financing · Scholarships