Dimensional Control in Reproduction Parts Course
Online 300-hour course in dimensional control of reproduction parts. 6 modules covering ISO 1101 (geometrical tolerances), ISO 2768-1 (general tolerances) and PC-DMIS. Assigned tutor and open enrolment.
Dimensional Control in Reproduction Parts Course — studying from Ireland
Ireland has an active heritage vehicle and classic machinery community, supported by clubs, restoration workshops and specialist suppliers serving classic cars, motorcycles and agricultural equipment. Engineering skills in this area combine historical knowledge with modern techniques in fabrication, materials and diagnostics. Restoration work is often linked to heritage conservation and museum collections, and classic vehicles operate under national roadworthiness and vehicle registration rules. Professional bodies and enthusiast organisations help maintain standards and knowledge across the sector.
Fees for Ireland: €448 (Euro), with instalments and employer sponsorship available.
Relevant bodies in Ireland
Typical roles
Questions from Ireland
Is there a recognised professional body in Ireland for classic vehicle restoration?
Classic vehicle restoration in Ireland is largely a craft and hobby sector, supported by enthusiast clubs and heritage bodies rather than a regulated professional title. SEIUM's qualifications are private and not accredited by any national body, so they do not confer membership or formal recognition. Check the requirements of any club or body you wish to join.
Would Irish restoration businesses or employers value this qualification?
Restoration businesses in Ireland often rely on hands-on skill, reputation and portfolio work. A private online qualification may add to your CV, but employers decide for themselves whether it is relevant. Your final project can help show your capability, though there is no guarantee of any outcome.
Can I study this part-time while keeping my current commitments?
Yes, the programme is 100% online and taught in English, so you can study from home around existing commitments. Durations are 300, 800 or 1,900 hours depending on the course, so plan your schedule accordingly. Fees can be paid in instalments, and each student has an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Define dimensional acceptance criteria for reproduction parts.
Interpret drawings with ISO dimensional and geometrical tolerances.
Select appropriate inspection instruments and fixtures.
Carry out incoming sampling plans and inspection.
Apply decision rules that account for measurement uncertainty.
Verify parts functionally through trial assembly.
Manage non-conformities and continuous improvement with suppliers.
Who it's for
- Dimensional control inspector who wants to specialise in Dimensional Control in Reproduction Parts.
- Metrology technician who wants to specialise in Dimensional Control in Reproduction Parts.
- Supplier quality manager who wants to specialise in Dimensional Control in Reproduction Parts.
- Spare parts reception technician who wants to specialise in Dimensional Control in Reproduction Parts.
- Quality engineer who wants to specialise in Dimensional Control in Reproduction Parts.
- Restoration workshop manager who wants to specialise in Dimensional Control in Reproduction Parts.
- Graduates in engineering or sciences seeking to enter the manufacture of reproduction spare parts.
What you'll work with
- ISO 1101 (geometrical tolerances)
- ISO 2768-1 (general tolerances)
- ISO 286-1 (ISO system of limits and fits)
- ISO 14253-1 (decision rules for conformity)
- ISO 2859-1 (sampling procedures for inspection by attributes)
- ISO 10360-2 (verification of coordinate measuring machines)
- ISO 9001 (quality management)
6 modules · 300 h
1.1Risk of fitting a part out of tolerance1.2Reproduction parts and their variability1.3Suppliers and their reliability1.4What is checked and what is not1.5Full inspection versus sampling1.6Cost of inspection and its justification1.7Reference documentation1.8Master part and its custody1.9Workshop responsibility1.10Workshop: incoming inspection plan
2.1Functional and free dimensions2.2Reasonable tolerances by part type2.3Fits with the mating part2.4Required surface finish2.5Declared material and treatment2.6Documentation that must accompany the part2.7Prior agreement with the supplier2.8What to do with a borderline part2.9Recording the criterion2.10Practice: acceptance criteria for three parts
3.1Callipers, micrometer and dial gauge3.2Go/no-go gauges3.3Surface plate and measuring column3.4Templates and counter-templates3.5Bespoke inspection fixtures3.6Coordinate measuring machine3.7Scanning and comparison with the model3.8Calibration of instruments3.9Measurement conditions3.10Practice: designing an inspection fixture
4.1Part preparation and cleaning4.2Measurement sequence4.3Number of parts to measure4.4Recording measurements4.5Data handling4.6Conforming and non-conforming parts4.7Identification and separation of batches4.8Communication with the supplier4.9Returns and their management4.10Practice: full inspection of a batch
5.1Dry-fit assembly test5.2Measured clearances and play5.3Torque values and distortion5.4Bench testing5.5Checking on the vehicle5.6Symptoms of an out-of-tolerance part5.7Adjusting the part versus rejection5.8Recording the verification5.9Documented final decision5.10Practice: functional verification of a part
6.1Supplier evaluation and approval6.2Incident history6.3Quality agreements6.4First article approval6.5Supplier audit6.6Cost of poor quality6.7Control indicators6.8Staff training6.9Documented real cases6.10Final project: dimensional control system for a workshop
How you'll learn
100 % online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetable: the learner progresses at their own pace within the intake, which allows it to be combined with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is PC-DMIS, Calypso (ZEISS), Minitab, advanced Excel, in free, academic or evaluation versions. Tests are studied using real incoming inspection procedures with callipers and micrometers, coordinate measuring machine measurement, and trial fitting on the vehicle. Assessment is continuous by module plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Define dimensional acceptance criteria for reproduction parts.
Interpret drawings with ISO dimensional and geometrical tolerances.
Select appropriate inspection instruments and fixtures.
Carry out incoming sampling plans and inspection.
Apply decision rules that account for measurement uncertainty.
Where this takes you
Requirements
- No prior qualification required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours spread over 3 to 5 months. That is between 10 and 15 hours a week on average, compatible with a full-time job.
The course uses PC-DMIS, Calypso (ZEISS), Minitab, advanced Excel. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM own diploma upon passing the continuous assessment and the integrating project. It is in-house training, not an official Ministry qualification.
Yes. Modules passed in a course or postgraduate diploma in the same area are credited towards the higher programme. Check the credit transfer policy when you enrol.
Related programmes
Climate Control in Classic Vehicle Storage Course
Online 300-hour course in climate control in classic vehicle storage. 6 modules covering EN 15757 (temperature and relative humidity for hygroscopic organic materials), EN 16893 (buildings…
Course in Strategies for Regularity Rallies
Online 300-hour course in strategies for regularity rallies. 6 modules covering the FIA International Sporting Code, the FIVA Event Code and advanced Excel. Assigned tutor and…
Course in Parts Documentation with Traceability
Online course of 300 h in parts documentation with traceability. 6 modules covering ISO 9001 (quality management systems), ISO/IEC 15459 (unique identifiers) and Odoo (inventory and…
More in Restoration & Classics
All Restoration & Classics programmes → · How to apply · Fees & financing · Scholarships