Diploma in Heavy-Duty Braking Energy Recovery
Online postgraduate diploma of 800 hours in Heavy-Duty Braking Energy Recovery: 8 modules covering heavy vehicle braking dynamics, retarders, electrical, hydraulic and mechanical recovery, blended braking control, thermal management and durability, and testing and validation, with an assigned technical tutor.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Quantify the energy available during braking of heavy vehicles.
Compare retarders and endurance braking systems.
Design electrical and hydraulic recovery systems.
Develop blended braking control strategies.
Analyse the thermal management and durability of components.
Plan validation and type-approval tests.
Assess recovery solutions technically and economically.
Who it's for
- Braking systems engineers.
- Heavy vehicle electrification engineers.
- Powertrain control engineers.
- Vehicle test engineers.
- Fleet energy efficiency specialists.
- Functional safety engineers.
- Engineering or science graduates looking to enter the mining sector.
What you'll work with
- UNECE Regulation R13 (braking of heavy vehicles)
- ISO 3450 (earth-moving machinery: braking systems)
- ISO 6469-3 (electrically propelled vehicles: electrical safety)
- ISO 19014 (earth-moving machinery: functional safety)
- UNECE Regulation R100 (electric power train safety)
- Directive 2006/42/EC (machinery)
- MATLAB/Simulink
- Simcenter Amesim
- GT-SUITE
- AVL CRUISE M
8 modules
1.1Kinetic and potential energy on descents1.2Load distribution and load transfer1.3Tyre adhesion and slip1.4Braking power and heat dissipation1.5Service, secondary and parking brakes1.6Duty cycles in mining and quarrying1.7Long gradients and endurance braking1.8UNECE R13 Type II tests1.9Energy balance of a dump truck1.10Workshop: calculating recoverable energy on a descent
2.1Engine brake and exhaust brake2.2Compression release brake2.3Hydrodynamic retarders2.4Electromagnetic retarders2.5Retarder and service brake integration2.6Retarder thermal management2.7Limitations on low-adhesion surfaces2.8Brake blending strategies2.9Comparison of solutions2.10Case study: selecting a retarder for a dumper
3.1Electric machines in generator mode3.2Bidirectional inverters3.3Batteries and supercapacitors3.4Braking resistors and choppers3.5State of charge and acceptance limits3.6Electric wheel drives in mining haul trucks3.7Trolley assist in mining3.8Full-cycle efficiency3.9Electrical safety to ISO 6469-33.10Practical exercise: sizing a supercapacitor bank
4.1Hydropneumatic accumulators in braking4.2Reversible pump-motors in the driveline4.3Flywheels4.4Hydraulic hybrid chassis systems4.5Clutches and disconnect devices4.6Losses and efficiency4.7Integration with service brakes4.8Applications in refuse collection vehicles4.9Electrical versus hydraulic comparison4.10Case study: refuse truck with hydraulic recovery
5.1Electronic braking system (EBS) architectures5.2Blending regenerative and friction braking5.3Priority and distribution between axles5.4Anti-lock braking with regenerative braking5.5Stability on descents and low traction5.6Driver response and pedal feel5.7CAN and SAE J1939 protocols5.8Diagnostics and degraded modes5.9Functional safety to ISO 190145.10Lab: brake blending simulation in Simulink
6.1Disc and drum temperature6.2Brake fade and its prevention6.3Retarder cooling6.4Battery heating during recovery6.5Lining wear and service life6.6Thermal models of components6.7Dynamometer bench tests6.8In-service monitoring6.9Predictive maintenance of the system6.10Practical exercise: thermal model of a brake on a descent
7.1System validation plan7.2Track and gradient tests7.3Measuring recovered energy7.4Instrumentation and data acquisition7.5Type-approval tests7.6Hardware-in-the-loop validation7.7Tests in extreme conditions7.8Analysis of results and correlation7.9Technical documentation7.10Case study: test campaign at a mine
8.1Defining the vehicle and the duty cycle8.2Baseline energy analysis8.3Selecting the recovery technology8.4Sizing the components8.5Control strategy8.6Full-cycle simulation8.7Economic and emissions assessment8.8Risks and validation plan8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
Training is 100% online on SEIUM's campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so the programme fits around your job.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is MATLAB/Simulink, Simcenter Amesim, GT-SUITE and AVL CRUISE M, in free, academic or evaluation versions. Exercises are based on real procedures for measuring recovered energy on quarry descents, simulating regenerative brake blending and bench thermal tests of brakes. Assessment is continuous by module, plus the final capstone project.
Standards covered: UNECE Regulation R13, ISO 3450, ISO 6469-3, ISO 19014, UNECE Regulation R100, Machinery Directive 2006/42/EC.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- Internet connection and a computer able to run the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with MATLAB/Simulink, Simcenter Amesim, GT-SUITE and AVL CRUISE M, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the programme software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in Explainable AI Applied to Fraud Prevention
Online postgraduate diploma of 800 hours in explainable AI applied to fraud prevention. 8 modules covering fraud typologies, predictive fraud models, global and local explainability, fairness…
Diploma in Energy Autonomy Strategies
Online postgraduate diploma of 800 hours in energy autonomy strategies for off-grid operations. 8 modules covering energy demand in isolated sites, on-site renewable generation, energy storage,…
Diploma in Operational Risk in Energy Infrastructure
Online postgraduate diploma of 800 hours in operational risk in energy infrastructure. 8 modules covering critical energy infrastructure, operational risk frameworks, process risk analysis, asset reliability,…
More in Off-Road, Special Vehicles & Machinery
All Off-Road, Special Vehicles & Machinery programmes → · How to apply · Fees & financing · Scholarships