Course in Destructive and Non-Destructive Testing of Materials
300-hour online course in destructive and non-destructive testing of materials. 6 modules covering ISO 6892-1 (tensile testing at room temperature), ISO 148-1 (Charpy impact test) and CIVA. Assigned tutor and open enrolment.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the fundamentals of materials characterisation.
Carry out and interpret destructive mechanical tests.
Apply metallography and failure analysis techniques.
Select the appropriate non-destructive testing method.
Interpret NDT indications against acceptance criteria.
Describe the qualification of procedures and personnel.
Develop an inspection plan for a nuclear component.
Who it's for
- Materials testing engineer who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Level 2 NDT inspector who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Failure analysis specialist who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- In-service inspection engineer who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Metallographic laboratory technician who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Welding quality engineer who wants to specialise in Destructive and Non-Destructive Testing of Materials.
- Engineering or science graduates seeking to enter nuclear power plants.
What you'll work with
- ISO 6892-1 (tensile testing at room temperature)
- ISO 148-1 (Charpy impact test)
- ISO 9712 (qualification of NDT personnel)
- ASME BPVC Section V (non-destructive examination)
- ASME BPVC Section XI (in-service inspection)
- ASTM E399 (fracture toughness KIc)
- ISO 17640 (ultrasonic testing of welded joints)
6 modules · 300 h
1.1What needs to be known about a material and which test reveals it1.2Destructive vs non-destructive testing: when each applies1.3Specimen, sampling and representativeness1.4Traceability, calibration and reference standards1.5Measurement uncertainty in mechanical testing1.6Test standards and laboratory accreditation1.7The test report: what it must contain to be valid1.8Acceptance criteria and material specification1.9Laboratory safety1.10Exercise: choosing the test battery for a specification
2.1Tensile: curve, yield strength, tensile strength and elongation2.2Brinell, Vickers and Rockwell hardness: which to use and why2.3Toughness and Charpy impact; transition temperature2.4Fatigue: S-N curves and governing factors2.5Creep and creep rupture at high temperature2.6Fracture mechanics and toughness measurement2.7Bend, flattening and drawing tests2.8Tests on welded joints2.9Effect of irradiation on mechanical properties2.10Practice: interpreting a set of tensile and impact results
3.1Sample preparation: cutting, mounting, polishing and etching3.2Optical and electron microscopy3.3Identification of phases and microstructure3.4Grain size, inclusions and defects3.5Chemical and compositional analysis3.6Fractography: learning to read the fracture surface3.7Failure mechanisms: fatigue, stress corrosion cracking and embrittlement3.8Ordered sequence of a failure investigation3.9Failure analysis report with defensible conclusions3.10Practice: analysing a real in-service fracture case
4.1Visual inspection and its scope, always underestimated4.2Liquid penetrant testing: procedure and limitations4.3Magnetic particle testing and ferromagnetic materials4.4Eddy currents and thickness measurement4.5Contact ultrasonics: probes and calibration4.6Advanced techniques: phased array and TOFD4.7Industrial radiography and digital radiography4.8Thermography and acoustic emission4.9Choosing the technique according to the defect sought4.10Practice: detecting and sizing defects in a specimen
5.1Qualification and certification of testing personnel5.2Written procedures and their approval5.3Qualification of inspection procedures5.4Inspection plans for manufacturing and in service5.5Inspection of pressure vessels and pipework5.6Remote inspection and inspection in radiation environments5.7Evaluation of indications and acceptance criteria5.8Fitness-for-service assessment5.9Recording, traceability and archiving of inspections5.10Practice: drafting an inspection procedure
6.1Choice of component and its service context6.2Material specification and applicable requirements6.3Destructive and non-destructive test plan6.4Execution and recording of tests6.5Joint interpretation of all results6.6Fitness-for-service assessment and remaining life estimation6.7Periodic inspection recommendations6.8Cost of the test plan6.9Technical report6.10Defence of the work
How you'll learn
100 % online training on the SEIUM campus, with downloadable material, recorded classes and a dedicated technical tutor. There are no fixed timetables: students progress at their own pace within the intake, which makes it possible to combine the programme with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is CIVA, Instron Bluehill, ImageJ/Fiji, UltraVision (Zetec), in free, academic or evaluation versions. Tests are studied using real procedures for tensile, hardness and Charpy testing, metallography and fractography, and ultrasonic and eddy current inspection. Assessment is continuous, module by module, plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the fundamentals of materials characterisation.
Carry out and interpret destructive mechanical tests.
Apply metallography and failure analysis techniques.
Select the appropriate non-destructive testing method.
Interpret NDT indications against acceptance criteria.
Where this takes you
Requirements
- No previous degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow the reading of technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours, spread over 3 to 5 months. That is between 10 and 15 hours per week on average, compatible with full-time work.
You work with CIVA, Instron Bluehill, ImageJ/Fiji, UltraVision (Zetec). Free, academic or evaluation versions are used, and the tutor indicates the open-source alternative where one exists.
SEIUM's own diploma upon passing the continuous assessment and the integrative project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised in the advanced programme. Check the recognition policy when enrolling.
Related programmes
Course on International Regulation in Nuclear Robotics
Online course of 300 h in International Regulation in Nuclear Robotics. 6 modules covering IEC 61513 (I&C systems important to safety), IEC 61508 (functional safety) and…
Course in Radiological Shielding Technology
Online 300-hour course in radiological shielding technology. 6 modules covering NCRP Report 147 (shielding of X-ray facilities), NCRP Report 151 (shielding of megavoltage facilities) and MicroShield.…
Breeding Blankets and Tritium Production Course
Online 300-hour course in breeding blankets and tritium production. 6 modules covering Décret n° 2012-1248 (authorisation for the creation of ITER, INB 174), Arrêté INB du…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships