Postgraduate Diploma in Gaps/Flush and Optical Measurement
Online 800-hour Postgraduate Diploma in Gaps/Flush and Optical Measurement. 8 modules covering ISO 1101:2017, ISO 5459:2011 and ZEISS INSPECT. Assigned tutor and open enrolment.
Postgraduate Diploma in Gaps/Flush and Optical Measurement — studying from Canada
Canada's motorcycle and two-wheeler market is relatively modest compared with the car sector, but it supports a network of dealers, distributors, parts suppliers and recreational riding communities. Manufacturers and importers serve markets across provinces, with seasonal demand shaped by climate. Engineering work in this area includes vehicle homologation, component design and electric two-wheeler development. Regulation of vehicle safety and emissions involves federal and provincial authorities.
Fees for Canada: C$2,330 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Is this programme recognised by professional bodies in Canada for motorcycle engineering?
SEIUM's qualifications are private, not official state degrees, and are not accredited by any national body in Canada. Vehicle engineering roles in Canada are generally not licensed by a single title-protected body, but employers and industry associations set their own expectations. Transport Canada regulates vehicle safety standards, which is separate from any qualification. Check recognition with prospective employers directly.
What career paths in Canada could this qualification support in the 2-wheeler sector?
Potential roles include design, testing, product development and technical support with motorcycle and powersports manufacturers, distributors and component suppliers. Whether a private qualification is valued is for each employer to decide, and experience often matters most in this sector. The final project can provide a concrete portfolio piece, though it does not guarantee any position.
How can I manage this programme alongside work in Canada?
The programme is entirely online and in English, so it suits students across Canadian time zones, and no student visa is needed to study from home. Workload ranges from 300 to 1,900 hours depending on the programme chosen. Fees are payable in instalments, and employer sponsorship is possible. An assigned technical tutor provides guidance throughout.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Define gap, flush and parallelism requirements for motorcycle joints.
Specify parts using GD&T according to the ISO GPS system.
Analyse tolerance stacks using worst-case, RSS and Monte Carlo methods.
Measure parts and assemblies with 3D optical scanners.
Evaluate measurement systems through R&R studies.
Apply statistical process control to dimensional quality.
Implement fit control plans on the assembly line.
Who it's for
- Dimensional quality engineer looking to specialise in Gaps/Flush and Optical Measurement.
- Metrology technician looking to specialise in Gaps/Flush and Optical Measurement.
- Tolerance engineer looking to specialise in Gaps/Flush and Optical Measurement.
- 3D optical measurement technician looking to specialise in Gaps/Flush and Optical Measurement.
- Assembly quality manager looking to specialise in Gaps/Flush and Optical Measurement.
- Supplier quality engineer looking to specialise in Gaps/Flush and Optical Measurement.
- Engineering or science graduates seeking to enter motorcycle manufacturing.
What you'll work with
- ISO 1101:2017
- ISO 5459:2011
- ISO 2768-1:1989
- ISO 10360-8:2013
- VDI/VDE 2634 Parte 3
- ISO 22514-2:2017
- ISO 14253-1:2017
- ASME Y14.5-2018
8 modules · 800 h
1.1Definition of gap, flush and parallelism1.2Visible joints between fairings, tank and tail section1.3Influence of fit on perceived quality1.4Differences in requirements by segment1.5Plastic-to-plastic and plastic-to-metal joints1.6Clips, screws and fastening elements1.7Effect of thermal expansion on clearances1.8Typical fit defects on the line1.9Benchmarking fits on premium motorcycles1.10Case study: visible joint map of a sport-touring
2.1ISO GPS system and specification language2.2Geometrical tolerances of form and position2.3Reference systems and datums2.43-2-1 referencing schemes2.5Surface profile for fairings2.6General tolerances to ISO 27682.7Specifying gap and flush on drawings2.8Tolerances for injection-moulded parts2.9Reading supplier drawings2.10Practice: GD&T dimensioning of a side cover
3.1One-dimensional dimensional chains3.2Worst-case method3.3Statistical RSS method3.4Monte Carlo variation simulation3.53DCS analysis software3.6Contributions and sensitivity analysis3.7Fit and compensation strategies3.8Robust design of fixings3.9Validation with production data3.10Workshop: tolerance analysis of a tank-to-fairing joint
4.1Structured light scanners4.2Portable laser scanners4.3Industrial photogrammetry with markers4.4Portable gap and flush sensors4.5Calibration and verification of equipment4.6Preparing shiny surfaces4.7CAD alignment and best fit4.8Colour deviation maps4.9Uncertainty in optical measurement4.10Laboratory: scanning a fairing with structured light
5.1Coordinate measuring machines5.2Articulated measuring arms5.3Check fixtures and cubing5.4Programming measurement routines5.5Comparison between touch-probe and optical measurement5.6Verification to ISO 103605.7System R&R studies5.8Report standardisation5.9Measurement traceability5.10Practice: R&R study of a gap gauge
6.1Statistical process control applied to fits6.2Cp and Cpk capability indices6.3Variables control charts6.4Root-cause analysis of dimensional deviation6.5Correlation between individual part and assembly6.6Correction loops for injection moulds6.7Real-time capture of measurement data6.8Dimensional quality dashboards6.9Communicating results to suppliers6.10Case study: mould correction using scan data
7.1In-line gap measurement stations7.2Robotic measurement automation7.3Sampling plans and frequencies7.4Finished product audit7.5Operator training in fitting7.6Dimensional requirements for suppliers7.7Engineering change management7.8Costs of dimensional quality7.9Continuous improvement with Kaizen methodology7.10Case study: gap control in final assembly
8.1Selection of the fairing assembly8.2Target gap and flush specification8.3Tolerance chain analysis8.4Optical measurement plan8.5Part scanning campaign8.6Statistical analysis of results8.7Proposal for design improvements8.8Production control plan8.9Report and presentation8.10Final review with the tutor
How you'll learn
Training 100 % online on the SEIUM campus, with downloadable material, recorded classes and assigned technical tutor. No fixed timetables: students progress at their own pace within the intake, which makes it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is ZEISS INSPECT, PolyWorks Inspector, 3DCS Variation Analyst, Creaform VXelements, Minitab, in free, academic or evaluation versions. Case studies are based on real 3D scanning procedures for fairings and comparison with CAD, tolerance chain analysis of real assemblies, and R&R studies of measurement systems. Assessment is continuous per module, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Define gap, flush and parallelism requirements for motorcycle joints.
Specify parts using GD&T according to the ISO GPS system.
Analyse tolerance stacks using worst-case, RSS and Monte Carlo methods.
Measure parts and assemblies with 3D optical scanners.
Evaluate measurement systems through R&R studies.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient Spanish to read technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 800 hours in total, spread over 6 to 8 months. That is between 10 and 15 hours per week on average, compatible with a full-time job.
You will work with ZEISS INSPECT, PolyWorks Inspector, 3DCS Variation Analyst, Creaform VXelements, Minitab. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
An own diploma from SEIUM upon passing the continuous assessment and the integrating project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or diploma in the same area are credited towards the advanced programme. Check the recognition policy when you enrol.
Related programmes
Postgraduate Diploma in Fatigue, K&C and NDT Testing for 2R
Online 800-hour Postgraduate Diploma in Fatigue, K&C and NDT Testing for 2R. 8 modules with ASTM E466, ASTM E739 and nCode DesignLife. Assigned tutor and open…
Postgraduate Diploma in PTW Accident Reconstruction and Forensic Data
Online 800-hour Postgraduate Diploma in PTW Accident Reconstruction and Forensic Data. 8 modules covering ISO 13232-1:2005, ISO 12353-1:2020 and PC-Crash. Assigned tutor and open enrolment.
Postgraduate Diploma in ECE 22.06: Testing, Materials and Validation
Online Postgraduate Diploma of 800 hours in ECE 22.06: Testing, Materials and Validation. 8 modules covering UNECE Regulation No. 22 (series 06), UNECE Regulation No. 22…
More in Motorcycles & 2-Wheelers
All Motorcycles & 2-Wheelers programmes → · How to apply · Fees & financing · Scholarships