Diploma in Naval Structural Strength and Vibration
Online postgraduate diploma of 800 hours in naval structural strength and vibration. 8 modules covering hull loads, longitudinal strength, buckling and fatigue, structural dynamics, on-board vibration, shock and finite element analysis, with an assigned technical tutor.
Diploma in Naval Structural Strength and Vibration — studying from Canada
Canada's defence sector is centred on procurement and sustainment through the Department of National Defence and Defence Research and Development Canada. Industrial activity spans land vehicles, naval systems, avionics and electronics, with firms in Ontario, Québec, Nova Scotia and British Columbia. Companies such as General Dynamics Land Systems Canada and Lockheed Martin Canada are notable employers, alongside a broad base of small and medium suppliers. Engineers work on systems integration, vehicle protection, logistics and sustainment, operating within strict security and export control frameworks.
Fees for Canada: C$1,700 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Which Canadian bodies or processes govern defence engineering recognition?
Defence engineering in Canada often involves government procurement and security clearances, and engineers typically hold provincial Professional Engineer licences where a title is required. SEIUM's qualifications are private and not official state degrees or accredited by a national body, so they do not confer licensing or clearance. Recognition is for employers or the relevant body to decide, so verify this first.
Would Canadian defence or land systems employers accept this training?
Canadian defence employers and contractors generally rely on security clearance, licensing and demonstrated experience. A private qualification may support your application, but it is unlikely to replace those requirements, and its acceptance is up to each employer. A SEIUM final project can help show applied skill, so discuss expectations with prospective employers early.
Can I study remotely while working, and what are the costs and language demands?
Yes, the programmes are fully online, so you can study from Canada or elsewhere without a student visa, and fit sessions around work. Specialist courses are 300 hours, postgraduate diplomas 800 and master's 1,900. Teaching is in English, supported by an assigned technical tutor. Fees are payable in instalments, and employer sponsorship may be available.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Understand the loads acting on a ship structure.
Calculate the longitudinal and local strength of the hull.
Analyse buckling, fatigue and fracture in naval structures.
Model the dynamic behaviour and vibration of the ship.
Apply regulatory vibration and shock criteria.
Use the finite element method on naval structures.
Plan structural tests and measurements on board.
Who it's for
- Naval structural engineers.
- Noise and vibration engineers.
- Finite element analysts.
- Classification society surveyors.
- Structural test engineers.
- Naval design engineers.
- Engineering or science graduates looking to enter naval defence.
What you'll work with
- ISO 6954 (guidelines for permissible mechanical vibration on ships)
- ISO 20283-5 (measurement of vibration on ships: habitability)
- MIL-STD-167-1A (mechanical vibration of shipboard equipment)
- MIL-DTL-901E (high-impact shock testing)
- ANEP-77 (NATO Naval Ship Code)
- Lloyd's Register Rules for Naval Ships (classification rules for naval ships)
- DNV Rules for Naval Vessels (classification rules for naval vessels)
- ANSYS Mechanical
- Abaqus
- MAESTRO
- Femap with Simcenter Nastran
- MATLAB
8 modules
1.1Hydrostatic loads1.2Wave loads1.3Bending moment and shear force1.4Slamming and impact loads1.5Equipment and operational loads1.6Ice loads1.7Spectral analysis of loads1.8Classification society rules1.9Design load cases1.10Case study: still-water bending moment calculation
2.1The hull girder2.2Section modulus2.3Allowable stresses2.4Plating and stiffeners2.5Grillages2.6Bulkheads2.7Superstructure structures2.8Materials: steels and aluminium2.9Hull-superstructure connections2.10Practical exercise: section modulus calculation
3.1Plate buckling3.2Buckling of stiffened panels3.3Ultimate hull girder strength3.4Fatigue in structural details3.5S-N curves for welded joints3.6The hot-spot stress method3.7Fracture mechanics3.8Corrosion and its effect3.9Crack inspection3.10Lab: fatigue assessment of a joint
4.1Degrees of freedom and natural modes4.2Hull girder vibration4.3Local vibration4.4Added mass of water4.5Structural damping4.6Forced response4.7Springing and whipping4.8Resonances4.9Experimental modal analysis4.10Practical exercise: modal analysis of a hull section
5.1Excitation sources: propellers and engines5.2Propeller pressure pulses5.3Machinery unbalance5.4ISO 6954 criteria5.5Measurement according to ISO 202835.6Equipment vibration to MIL-STD-167-1A5.7Isolation and dampers5.8Structure-borne noise5.9Crew comfort5.10Lab: vibration measurement in accommodation spaces
6.1Underwater shock: general concepts6.2MIL-DTL-901E testing6.3Shock qualification of equipment6.4Shock mounts6.5Dynamic response to impact6.6Structural survivability6.7Residual strength after damage6.8Explicit simulation6.9Naval shock requirements6.10Case study: shock requirements for shipboard equipment
7.1Global hull modelling7.2Fine local modelling7.3Boundary conditions7.4Model validation7.5Non-linear analysis7.6Scale-model testing7.7On-board structural health monitoring7.8Structural digital twin7.9Documentation for classification7.10Workshop: finite element model of a block
8.1Definition of the vessel8.2Load calculation8.3Longitudinal strength8.4Fatigue analysis8.5Modal analysis8.6Vibration assessment8.7Shock requirements8.8Structural report8.9Report and presentation8.10Final project: final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within each intake, so it fits around your job.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is ANSYS Mechanical, Abaqus, MAESTRO, Femap with Simcenter Nastran and MATLAB, in free, academic or evaluation versions. Practical work is based on real procedures: modal analysis of a hull section, vibration measurement in accommodation spaces and fatigue strength assessment of a structural joint. Assessment is continuous by module, plus the final integrating project.
Standards covered: ISO 6954, ISO 20283-5, MIL-STD-167-1A, MIL-DTL-901E, ANEP-77, Lloyd's Register Rules for Naval Ships, DNV Rules for Naval Vessels.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- An internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours over 6–8 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with ANSYS Mechanical, Abaqus, MAESTRO, Femap with Simcenter Nastran and MATLAB, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute diploma, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
Prior technical training or professional experience in the sector (no university degree required), a computer able to run the programme software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Diploma in CBRN Protection Materials and Validation
Online postgraduate diploma of 800 hours in CBRN protection materials and their validation. 8 modules covering CBRN protection principles, barrier materials, adsorbent and filter materials, test…
Diploma in Military Information Classification
Online postgraduate diploma of 800 hours in military information classification, structured in 8 modules covering classification fundamentals, the Spanish legal framework, classification criteria, NATO and EU…
Diploma in Defence Supplier Auditing
Online postgraduate diploma of 800 hours in defence supplier auditing, structured in 8 modules covering the defence supply chain, AQAP quality requirements, audit techniques, special processes,…
More in Defense, Military Engineering & Land Systems
All Defense, Military Engineering & Land Systems programmes → · How to apply · Fees & financing · Scholarships