Course in Superconducting Technologies in Fusion
Online 300-hour course in superconducting technologies in fusion. 6 modules covering IEC 61788-1 (critical current in Nb-Ti conductors), IEC 61788-2 (critical current in Nb3Sn conductors) and COMSOL Multiphysics (AC/DC). Assigned tutor and open enrolment.
Course in Superconducting Technologies in Fusion — studying from Canada
Canada is a global leader in nuclear technology, most notably through CANDU reactor design and the development of medical isotopes. Ontario operates the largest nuclear fleet in the country, with major facilities at Pickering, Darlington and Bruce, while Atomic Energy of Canada Limited leads reactor research at Chalk River. The Canadian Nuclear Safety Commission regulates all nuclear activity. Engineers work on reactor design, fuel cycle technologies, decommissioning and radiation protection.
Fees for Canada: C$852 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Is this programme recognised by professional bodies in Canada for nuclear engineering?
SEIUM's qualifications are private, not official state degrees, and carry no national accreditation in Canada. Nuclear activities are regulated by the Canadian Nuclear Safety Commission, and professional engineering titles are provincially regulated. Nuclear roles often require specific licences or clearances, which a private qualification does not provide. Confirm with employers or the regulator.
Could this qualification help with nuclear career opportunities in Canada?
Canadian nuclear operators, utilities, fuel cycle firms and regulators' supplier networks employ engineers, but they set their own criteria. Many nuclear roles prioritise experience, security clearances and regulator-recognised training. The programme can add technical depth to your profile, but it does not guarantee entry or advancement in this tightly regulated field.
Can I study this online from Canada, and what is the workload?
Yes, the programme is 100% online and taught in English, and no student visa is required if you study from home. Specialist courses are 300 hours, postgraduate diplomas 800 hours and master's programmes 1,900 hours. Fees are payable in instalments, employer sponsorship is possible, and you receive an assigned technical tutor for guidance.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Explain the fundamentals of applied superconductivity.
Compare low- and high-critical-temperature superconductors.
Conceptually design toroidal and poloidal field coils.
Analyse quench detection and protection.
Size cryogenic cooling systems.
Interpret critical current measurements according to IEC 61788.
Assess the role of REBCO superconductors in compact tokamaks.
Who it's for
- Superconducting magnet engineer who wants to specialise in Superconducting Technologies in Fusion.
- Cryogenic engineer who wants to specialise in Superconducting Technologies in Fusion.
- Superconducting materials researcher who wants to specialise in Superconducting Technologies in Fusion.
- Magnet protection engineer who wants to specialise in Superconducting Technologies in Fusion.
- Fusion magnet researcher who wants to specialise in Superconducting Technologies in Fusion.
- Cryogenic test technician who wants to specialise in Superconducting Technologies in Fusion.
- Engineering or science graduates seeking to enter nuclear fusion.
What you'll work with
- IEC 61788-1 (critical current in Nb-Ti conductors)
- IEC 61788-2 (critical current in Nb3Sn conductors)
- IEC 60050-815 (superconductivity vocabulary)
- ISO 21009 (static cryogenic vessels)
- EN 13458 (vacuum-insulated cryogenic vessels)
- ASME BPVC Section III, Division 4 (fusion devices)
6 modules · 300 h
1.1Zero resistance and the Meissner effect1.2Type I and type II superconductors1.3Critical temperature, field and current density1.4Critical surface and vortex pinning1.5BCS theory and coherence length1.6Low-temperature superconductors: NbTi and Nb3Sn1.7High-temperature superconductors: REBCO and Bi-22121.8MgB2 and intermediate applications1.9Strain dependence in Nb3Sn1.10Practice: reading Jc(B,T) curves of conductors
2.1ITER cable-in-conduit conductors (CICC)2.2Multifilamentary wires and copper stabiliser2.3REBCO tapes and VIPER and CroCo cables2.4AC losses and coupling2.5Cryogenic stability and temperature margin2.6Current sharing and resistive transition2.7Superconducting joints and splices2.8Reaction heat treatment of Nb3Sn2.9Qualification tests at SULTAN2.10Workshop: calculating the temperature margin of a CICC
3.1Toroidal and poloidal field coils3.2Central solenoid and magnetic flux3.3Electromagnetic loads and Lorentz forces3.4Mechanical structure and coil cases3.5Electrical insulation and epoxy materials3.6Toroidal field ripple3.7High-field HTS magnets: SPARC3.8Magnet design for stellarators: W7-X3.9Error field correction coils3.10Case study: sizing a TF coil
4.1Supercritical helium cooling4.2Cryogenic plants and distribution4.3Thermal shields and cryostat4.4Nuclear heat load on the magnets4.5Quench detection and response times4.6Fast discharge and dump resistors4.7Heating and pressure during quench4.8Protection of HTS magnets: partial insulation4.9Cryogenic and diagnostic instrumentation4.10Laboratory: quench propagation simulation
5.1ITER magnets: manufacturing and lessons learned5.2JT-60SA and the manufacture of NbTi coils5.3EAST and KSTAR as superconducting tokamaks5.4Wendelstein 7-X and non-planar coils5.5SPARC and the 20 T TF magnet5.6European DEMO and CFETR programmes5.7Neutron irradiation damage in superconductors5.8Power supplies and switching5.9Costs and supply chain5.10Case study: testing the SPARC TF model coil
6.1Definition of device requirements6.2Superconductor selection6.3Conductor and cable design6.4Field and force calculation6.5Mechanical coil design6.6Cryogenic cooling scheme6.7Quench protection system6.8Technical risk assessment6.9Report and presentation6.10Final review with the tutor
How you'll learn
100 % online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: students progress at their own pace within the intake, which makes it possible to combine the course with work.
Each module combines theory, guided reading of the original standard and applied exercises. The software used is COMSOL Multiphysics (AC/DC), Opera (Simulia), ROXIE, THEA (CryoSoft), ANSYS Mechanical, in free, academic or evaluation versions. Tests are studied using real procedures for critical current measurements, quench tests on prototype magnets and cryogenic characterisation. Assessment is continuous, module by module, plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Explain the fundamentals of applied superconductivity.
Compare low- and high-critical-temperature superconductors.
Conceptually design toroidal and poloidal field coils.
Analyse quench detection and protection.
Size cryogenic cooling systems.
Where this takes you
Requirements
- No prior degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme consists of 300 hours in total, spread over 3 to 5 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
You will work with COMSOL Multiphysics (AC/DC), Opera (Simulia), ROXIE, THEA (CryoSoft) and ANSYS Mechanical. Free, academic or evaluation versions are used, and the tutor will indicate the free alternative where one exists.
A SEIUM Institute diploma upon passing the continuous assessment and the integrating project. This is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or Postgraduate Diploma in the same area are recognised towards the advanced programme. Check the recognition policy when you enrol.
Related programmes
Course on International Regulations in ITER/DEMO Projects
Online 300-hour course in international regulations for ITER/DEMO projects. 6 modules covering the ITER Agreement of 2006 (establishment of the ITER Organization), Décret n.º 2012-1248 (authorisation…
Stellarators Course and Its Academic Potential
Online 300-hour course on stellarators and its academic potential. 6 modules covering ASME BPVC Section III, Division 4 (fusion devices), RCC-MRx (mechanical design of high-temperature components)…
Course in Ethics in the Use of AI in Nuclear Safety
Online 300-hour course in ethics in the use of AI in nuclear safety. 6 modules with Regulation (EU) 2024/1689 (artificial intelligence), ISO/IEC 42001:2023 (AI management systems)…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships