Course in Robotics for Nuclear Decommissioning
Online course of 300 hours in robotics for nuclear decommissioning. 6 modules covering nuclear decommissioning, robotic platforms, perception and characterisation, control and teleoperation, safety, waste and verification, and a robotic deployment project, with an assigned technical tutor.
Course in Robotics for Nuclear Decommissioning — studying from Canada
Canada is a global leader in nuclear technology, most notably through CANDU reactor design and the development of medical isotopes. Ontario operates the largest nuclear fleet in the country, with major facilities at Pickering, Darlington and Bruce, while Atomic Energy of Canada Limited leads reactor research at Chalk River. The Canadian Nuclear Safety Commission regulates all nuclear activity. Engineers work on reactor design, fuel cycle technologies, decommissioning and radiation protection.
Fees for Canada: C$1,160 (Canadian dollar), with instalments and employer sponsorship available.
Relevant bodies in Canada
Typical roles
Questions from Canada
Is this programme recognised by professional bodies in Canada for nuclear engineering?
SEIUM's qualifications are private, not official state degrees, and carry no national accreditation in Canada. Nuclear activities are regulated by the Canadian Nuclear Safety Commission, and professional engineering titles are provincially regulated. Nuclear roles often require specific licences or clearances, which a private qualification does not provide. Confirm with employers or the regulator.
Could this qualification help with nuclear career opportunities in Canada?
Canadian nuclear operators, utilities, fuel cycle firms and regulators' supplier networks employ engineers, but they set their own criteria. Many nuclear roles prioritise experience, security clearances and regulator-recognised training. The programme can add technical depth to your profile, but it does not guarantee entry or advancement in this tightly regulated field.
Can I study this online from Canada, and what is the workload?
Yes, the programme is 100% online and taught in English, and no student visa is required if you study from home. Specialist courses are 300 hours, postgraduate diplomas 800 hours and master's programmes 1,900 hours. Fees are payable in instalments, employer sponsorship is possible, and you receive an assigned technical tutor for guidance.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Describe the phases and technical challenges of nuclear decommissioning.
Select robotic platforms suited to each decommissioning task.
Apply perception and radiological characterisation techniques with robots.
Design control and teleoperation schemes with haptic feedback.
Assess the radiation tolerance of electronic components and sensors.
Integrate safety, waste management and verification requirements into the robotic system.
Develop a capstone project for a robotic decommissioning system.
Who it's for
- Nuclear robotics engineers.
- Teleoperation engineers.
- Decommissioning specialists.
- Machine vision engineers.
- Radiological characterisation technicians.
- Remote handling systems engineers.
- Engineering or science graduates aiming to enter nuclear decommissioning.
What you'll work with
- ISO 10218-1 and ISO 10218-2 (industrial robot safety)
- IAEA GSR Part 6 (decommissioning of facilities)
- IEC 61508 (functional safety)
- ISO/TS 15066 (collaborative robots)
- IEC 60204-1 (electrical equipment of machines)
- ISO 13849-1 (safety-related parts of control systems)
- ROS 2
- Gazebo
- RoboDK
- MATLAB/Simulink
- CloudCompare
6 modules · 300 h
1.1Phases: shutdown, preparation, dismantling and closure1.2Immediate and deferred dismantling strategies1.3Radiological characterisation of the facility1.4Hostile environments: dose, contamination and confinement1.5The ALARA principle as justification for robotics1.6Cases: Fukushima Daiichi, Sellafield and José Cabrera1.7Requirements of IAEA GSR Part 61.8Role of ENRESA and the CSN in Spain1.9Regulations on the transport of radioactive waste1.10Case study: dose avoided through remote handling
2.1Master–slave telemanipulators2.2Heavy-payload hydraulic arms2.3Tracked ground vehicles2.4Snake robots and long-reach arms2.5Drones for radiological mapping2.6Underwater vehicles for fuel pools2.7Radiation hardening of electronics2.8Cutting, gripping and decontamination tools2.9Dual-arm manipulators2.10Workshop: platform selection for a hot cell
3.1Gamma detectors and gamma cameras3.2Fusion of radiological maps with LiDAR3.3SLAM in degraded environments3.4Machine vision under adverse lighting and radiation3.5Contact and force sensors3.6Material identification and activity estimation3.7Digital twin of the facility3.8Uncertainty in radiological measurement3.9Non-destructive testing in active environments3.10Lab: 3D dose map with ROS
4.1Bilateral teleoperation and haptic feedback4.2Latency and stability of remote control4.3Shared and supervised autonomy4.4Constrained trajectory planning4.5Virtual and augmented reality for operators4.6Workload and human factors4.7Force control in cutting and dismantling4.8Recovery from robot failures4.9AI-assisted task planning4.10Practical exercise: teleoperated cutting in a simulator
5.1Secondary waste generated by cutting5.2Decontamination of the robot itself5.3Failure mode and effects analysis (FMEA)5.4Software verification and validation5.5Functional safety according to IEC 615085.6Recovery of broken-down robots5.7Project costs and planning5.8Lessons learnt at Fukushima Daiichi5.9Operator training and certification5.10Case study: FMEA of a hydraulic manipulator
6.1Description of the decommissioning scenario6.2Baseline radiological characterisation6.3Selection of platform and tools6.4Design of the perception system6.5Control and teleoperation strategy6.6Safety and waste management plan6.7Estimate of dose, timeline and costs6.8Simulation of the work sequence6.9Report and presentation6.10Final project: final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. There are no fixed timetables: you progress at your own pace within the intake, so you can combine it with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is ROS 2, Gazebo, RoboDK, MATLAB/Simulink and CloudCompare (point clouds), in free, academic or evaluation versions. Practice is based on real procedures: teleoperation simulation in a virtual environment, radiological characterisation with on-board sensors, and cutting and remote handling mock-ups. Assessment is continuous by module, plus the final project.
Standards covered: ISO 10218-1 and ISO 10218-2, IAEA GSR Part 6, IEC 61508, ISO/TS 15066, IEC 60204-1, ISO 13849-1.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Where this takes you
Requirements
- No prior qualification is required.
- Internet connection and a computer capable of running the programme software.
- English sufficient to read technical standards.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 300 hours over 3 months. You set your own pace within each intake, and your tutor helps you plan the workload around your job.
You work with ROS 2, Gazebo, RoboDK, MATLAB/Simulink and CloudCompare, using free, academic or evaluation versions. Your tutor indicates the free alternative wherever one exists.
A SEIUM Institute certificate, awarded on passing the continuous assessment and the final project. It is SEIUM's own qualification, not an official state degree; its recognition depends on the programme completed and the regulations of each country.
Yes. Modules passed are recognised in a higher programme in the same area (postgraduate diploma or master's). Ask about the recognition policy when you enrol.
No prior qualification is required; you need a computer able to run the programme software and English sufficient to read technical standards.
Start dates are set by SEIUM's faculty for each intake. Our admissions team will confirm the next available date when you apply.
Related programmes
Course on European Nuclear Energy Regulation (EURATOM)
Online course of 300 h in European Nuclear Energy Regulation (EURATOM). 6 modules covering Treaty establishing the European Atomic Energy Community (Euratom), Directive 2009/71/Euratom, as amended…
Course in Thermal Efficiency in Nuclear Rankine Cycles
Online 300-hour course in thermal efficiency in nuclear Rankine cycles. 6 modules covering ASME PTC 6 (steam turbine performance testing), ASME PTC 12.2 (steam condensers) and…
Course in Low- and Intermediate-Level Waste Management
Online 300-hour course in low- and intermediate-level waste management. 6 modules with IAEA SSG-29 (near-surface disposal facilities), IAEA GSG-1 (classification of radioactive waste) and Genie 2000…
More in Nuclear Engineering & Nuclear Fuel Cycle Technologies
All Nuclear Engineering & Nuclear Fuel Cycle Technologies programmes → · How to apply · Fees & financing · Scholarships